- 您現在的位置：買賣IC網 > PDF目錄365499 > SAI01-1 (Sanken Electric Co.,Ltd.) Surface-mount and Separate Excitation Type PDF資料下載
參數資料
| 型號： | SAI01-1 |
| 廠商： | Sanken Electric Co.,Ltd. |
| 英文描述： | Surface-mount and Separate Excitation Type |
| 中文描述： | 表面貼裝及獨立激勵型 |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 71K |
| 代理商： | SAI01-1 |
74
I
Selecting External Components
1. Inductor L
1
1) It must be suited for switching regulators.
Do not use inductors as noise filters as they generate excessive heat.
2) It must have the appropriate inductance value.
If the inductance is too small (150
μ
H or lower), abnormal oscillation may occur causing operation problems in the overcurrent protection
circuit within the rated current range.
3) The rated current must be satisfied.
If the rated current is exceeded, magnetic saturation leads to overcurrent.
2. Capacitors C
1
and C
2
1) They must satisfy the withstand voltage and allowable ripple current.
Exceeding the ratings of these capacitors or using them without derating shortens their service lives and may also cause abnormal
oscillation of the IC.
2) C
2
must be a low-impedance type capacitor.
A low-impedance type capacitor is recommended for C
2
to ensure minimum ripple voltage and stable switching operation.
3. Diode D
1
The Sanken SFPB54 diode is recommended for D
1
. If you intended to use an equivalent diode, be sure to use a Schottky Barrier diode and
make sure that the reverse voltage applied to terminal 2 of the IC does not exceed the value (–1V) given in the absolute maximum ratings. If
you use a fast recovery diode or any other diode, application of a reverse voltage generated from the recovery or ON voltage of the diode may
damage the IC.
Application
Variable output voltage
Output voltage can be adjusted in the same way as SI-8000S in page 85.
I
Example of Printed Circuit Board
a) For optimum operation, there must be only
one GND line originating from terminal 4
and each component must be connected
with the shortest possible wiring.
b) To prevent heating of the IC, it is best to
make the GND pattern as large as pos-
sible since the internal frame and termi-
nal 4 (GND) are connected to each other.
I
T
a
-P
D
Characteristics
The efficiency depends on the input voltage and the out-
put current. Thus, obtain the value from the efficiency
graph on page 75 and substitute the percentage in the
formula above.
V
O
:Output voltage
I
O
:Output current
η
x:Efficiency (%)
V
F
:Diode forward voltage
SFPB54-0.3V
Thermal design for D
1
must be considered separately.
+
+
V
IN
DI
1
C
1
L
1
C
2
GND
SW
V
O
1
2
3
4
SAI
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
Ambient Temperature T
a
(
°
C)
25
50
75
100
125
P
D
Glass epoxy
substrate
(95
×
69
×
1.2)
Natural cooling
G
SAI Series
P
D
=V
O
I
O
100 –1 –V
F
I
O
1– V
O
ηχ
V
IN
相關PDF資料 |
PDF描述 |
|---|---|
| SAI02 | Surface-mount and Separate Excitation Type |
| SAI05 | Surface-mount and Separate Excitation Type |
| SAI03 | 12V,Surface Mount Switching Regulator IC |
| SAI04 | 15V,Surface Mount Switching Regulator IC |
| SAI06 | 9V,Surface Mount Switching Regulator IC(9v,表貼開關穩壓器芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAI01V1 | 制造商:Sanken Electric Co Ltd 功能描述:IC REG BUCK 5V 0.5A PS-4PIN |
| SAI02 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface-mount and Separate Excitation Type |
| SAI02V1 | 制造商:Sanken Electric Co Ltd 功能描述:IC REG BUCK 3.3V 0.5A PS-4PIN |
| SAI03 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface-mount and Separate Excitation Type |
| SAI03V1 | 制造商:Sanken Electric Co Ltd 功能描述:IC REG BUCK 12V 0.4A PS-4PIN |
發布緊急采購，3分鐘左右您將得到回復。