- 您現在的位置：買賣IC網 > PDF目錄365496 > SAFUxxxx (Murata Manufacturing Co., Ltd.) CERAMIC MICROWAVE FILTERS SAW FILTERS PDF資料下載
參數資料
| 型號： | SAFUxxxx |
| 廠商： | Murata Manufacturing Co., Ltd. |
| 英文描述： | CERAMIC MICROWAVE FILTERS SAW FILTERS |
| 中文描述： | 陶瓷微波濾波器SAW濾波器 |
| 文件頁數： | 5/5頁 |
| 文件大小： | 150K |
| 代理商： | SAFUXXXX |
CERAMIC MICROWAVE FILTERS
SAW FILTERS
ENVIRONMENTAL SPECIFICATIONS
MECHANICAL
TEST ITEM
PACKAGE
TEST CONDITIONS
TEST METHOD
Filter is soldered onto the center of PCB which is laid on two small supporters
spaced 90mm apart. The PCB is deflected to 1mm below the horizontal level by the
pressing stick for 1 second and repeated 5 times.
A force of 1.0 Kg shall be applied to each terminal in the direction of the axis of
terminal for 30 ± 5 seconds.
A force of 250 gf is applied to each lead in axial direction. The lead shall be bent
90 degrees to one direction, then in opposite direction and returned to the
original position.
Lead terminals are immersed in methanol with 7 to 10% of rosin flux for about
5 seconds, then immersed in soldering bath at 230 ± 5°C for 5 ± 0.5 seconds.
Drop 3 times on concrete floor from 1.0 meter, (30cm for some products).
Vibration amplitude of 1.5mm at 10-55Hz in each of three mutually
perpendicular directions for 1 hour.
SMD
Terminal Strength
LEADED
Solderability
BOTH
MIL-STD-202E
Method 208C
Random Drop
BOTH
Vibration
BOTH
MIL-STD-201E
Method 201A
ENVIRONMENTAL
TEST ITEM
PACKAGE
TEST CONDITIONS
TEST METHOD
MIL-STD-202E
Method 101D
MIL-STD-202E
Method 102A
MIL-STD-202E
Method 103B
Salt Spray
BOTH
Hold in chamber with 5% salt density at 35°C +1.1°/–1.7°C for 48 hours.
Measure after exposure to room condition for 1 hour.
Exposure to 5 cycles of –55°C (30 minutes)
+25°C (15 minutes), ±85°C
(30 minutes)
+25°C (15 minutes). Test after 2 hours exposure to room conditions.
Hold in chamber with 90 to 95% R.H. at 40 ± 2°C for 100 hours. Test after 2
hours exposure to room conditions.
Hold in chamber with 90 to 95% R.H. at 40 ± 2°C for 100 hours at 6VDC.
Test after 2 hours exposure to room conditions.
Expose to 5 cycles of –55°C (30 minutes)
+85°C (30 minutes). Test after 2 hours
exposure to room conditions.
Hold in chamber at 85 ± 2°C for 100 hours. Test after exposure to room
conditions for 2 hours.
Hold in chamber at –30 ± 2°C for 100 hours. Test after exposure to room
conditions for 2 hours.
Hold in chamber at 85 ± 2°C for 100 hours at 6VDC. Test after exposure to room
conditions for 2 hours.
Hold in chamber with 1000ppm sulfur density for 24 hours. Test after exposure
to room conditions for 2 hours.
Filter shall be preheated at 150 ± 20°C for 60 seconds, immersed whole
electrode in soldering bath at 240 ± 5°C for 3 ± 1 seconds, then measured after
exposure to room conditions for 2 hours.
Lead terminals are immersed up to 1.5mm from package base in soldering bath
at 260 ± 5°C for 10 ± 1 seconds, then measured after exposure to room
conditions for 2 hours.
Temperature Cycling
BOTH
Humidity
BOTH
Operating Humidity
BOTH
MIL-STD-202E
Thermal Shock
BOTH
MIL-STD-202E
Method 107D
MIL-STD-202E
Method 108A
MIL-STD-202E
Method 108A
Life Test (High)
BOTH
Life Test (Low)
BOTH
Operating Life Test
BOTH
Sulfuration
BOTH
SMD
Resistance to
Soldering Heat
MIL-STD-202E
Method 210A
LEADED
TEST ITEM
PACKAGE
TEST CONDITIONS
TEST METHOD
Dielectric Withstanding
Voltage
BOTH
Apply 100VDC between I/O terminals and ground terminal, for 1 minute.
MIL-STD-202E
Insulation Resistance
BOTH
Apply 100VDC between I/O terminals and ground terminal, for 1 minute.
MIL-STD-202E
Method 302
Temperature
Characteristics
SMD
Filter shall be measured between –10°C to +60°C temperature range.
LEADED
Filter shall be measured between –10°C to +50°C temperature range.
ELECTRICAL
354
CG01-I
SAF Series
相關PDF資料 |
PDF描述 |
|---|---|
| SAFU1842.5A70STC11 | LJT 79C 79#22D PIN WALL RECP |
| SAFU1842.5A70STC12 | LJT 79C 79#22D PIN PLUG |
| SAFU1842.5A70TTC | LJT 79C 79#22D PIN PLUG |
| SAFU1842.5A70TTC00 | Circular Connector; No. of Contacts:79; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:21; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:21-35 RoHS Compliant: No |
| SAFU1842.5A70TTC02 | CERAMIC MICROWAVE FILTERS SAW FILTERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAFWLK | 制造商:3M Electronic Products Division 功能描述:3M(TM) Safety-Walk Edge Sealing Compound |
| SAF-XC161CJ-16F20F | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller |
| SAF-XC161CJ-16F20F BB | 功能描述:IC MCU 16BIT FLASH TQFP-144-19 RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:XC16x 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| SAFXC161CJ16F20FAC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| SAFXC161CJ16F20FBB | 功能描述:16位微控制器 - MCU XC166 CISC 128KB FLASH 20MHZ 5V RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。