- 您現在的位置：買賣IC網 > PDF目錄372115 > SAA7335 (NXP Semiconductors N.V.) DSP for CD and DVD-ROM systems(在CD和DVD-ROM應用中的DSP) PDF資料下載
參數資料
| 型號： | SAA7335 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | DSP for CD and DVD-ROM systems(在CD和DVD-ROM應用中的DSP) |
| 中文描述： | DSP的CD和DVD - ROM的系統（在光盤和DVD - ROM光碟應用中的數字信號處理器） |
| 文件頁數： | 9/36頁 |
| 文件大?。?/td> | 196K |
| 代理商： | SAA7335 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
1997 Aug 11
9
Philips Semiconductors
Preliminary specification
DSP for CD and DVD-ROM systems
SAA7335
Microcontroller interface
The SAA7335 has two microcontroller interfaces, one
serial I
2
C-bus and one parallel (8051 microcontroller
compatible).
The two communication modes may be operated at the
same time, the modes are described below:
1.
Parallel mode: protocol compatible with 8052
multiplexed bus:
a) da0 to da7 = address/data bus
b) ALE = Address Latch Enable, latches the address
information on the bus
c) WRi = active LOW write signal for write to
SAA7335
d) RDi = active LOW read signal for read from
SAA7335
e) CSi = active HIGH Chip Select signal (this signal
gates the RDi and WRi signals).
2.
I
2
C-bus mode: I
2
C-bus protocol where SAA7335
behaves as slave device where:
a) SDA = I
2
C-bus data
b) SCL = I
2
C-bus clock
c) I
2
C-bus slave address (write mode) = 3EH
d) I
2
C-bus slave address (read mode) = 3FH
e) Maximum data transfer rate = 400 kbits/s.
M
ICROCONTROLLER INTERFACE
(I
2
C-
BUS MODE
)
Bytes are transferred over the interface in single bytes of
which there are two types; write data commands and read
data commands.
The sequence for a write data command (1 data byte) is as
follows:
Send START condition
Send address 3EH (write)
Write command address byte
Write data byte
Send STOP condition.
The sequence for a read data command (that reads 1 data
byte) is as follows:
Send START condition
Send address 3EH (write)
Write status address byte
Send STOP condition
Send START condition
Send address 3FH (read)
Read data byte
Send STOP condition.
R
EADING AND WRITING DATA TO THE
SAA7335
The SAA7335 has 32
×
8-bit configuration and status
registers as shown in Table 1. Not all locations are
currently defined and some remain reserved for future
upgrades. These can be written to or read from via the
microcontroller interface using either the serial or parallel
control bus.
相關PDF資料 |
PDF描述 |
|---|---|
| SAA7341 | COMS Digital decoding IC for Compact Disc |
| SAA7341GP | COMS Digital decoding IC for Compact Disc |
| SAA7345 | Bitstream conversion ADC for digital audio systems |
| SAA7345GP | Bitstream conversion ADC for digital audio systems |
| SAA7366T | Bitstream conversion ADC for digital audio systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA7335GP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DSP for CD and DVD-ROM systems |
| SAA7341 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:COMS Digital decoding IC for Compact Disc |
| SAA7341GP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:COMS Digital decoding IC for Compact Disc |
| SAA7345 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Bitstream conversion ADC for digital audio systems |
| SAA7345GP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Bitstream conversion ADC for digital audio systems |
發布緊急采購，3分鐘左右您將得到回復。