- 您現在的位置：買賣IC網 > PDF目錄372110 > SAA5297A (NXP Semiconductors N.V.) Economy teletext and TV microcontrollers PDF資料下載
參數資料
| 型號： | SAA5297A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Economy teletext and TV microcontrollers |
| 中文描述： | 經濟圖文電視和電視微控制器 |
| 文件頁數： | 44/68頁 |
| 文件大?。?/td> | 612K |
| 代理商： | SAA5297A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
1997 Jul 07
44
Philips Semiconductors
Preliminary specification
Economy teletext and TV microcontrollers
SAA5x9x family
9.14
On Screen Display boxes
The size implying OSD control characters (BCH to BFH)
are intended to allow OSD messages to be displayed with
the minimum disruption to the teletext page stored in the
page memory. OSD boxes are not the same as teletext
boxes created using the teletext boxing control characters
(0AH and 0BH).
When one of these characters occurs the display size
changes appropriately (to normal size for BCH, double
height for BDH, double width for BEH and double size for
BFH) and an OSD box starts from the next character
position (‘set after’). The OSD box ends either at the end
of the row of text or at the next size implying OSD
character. When an OSD box is ended using another size
implying OSD character the box ends at the position of the
control character (‘set at’). This arrangement allows
displays to be created without blank spaces at the ends of
the OSD boxes.
To prevent control characters from the teletext page
affecting the display of the OSD message the flash,
teletext box, conceal, separated graphics, twist and hold
graphics functions are all reset at the start of an OSD box,
as they are at the start of the row. In order to allow the most
commonly used display attributes to be set up before the
box starts the foreground colour, background colour and
mosaics on/off attributes are not reset.
The text within an OSD box is always displayed in text
mode i.e. as if the Text On and Bkgnd On bits are both set
to a logic 1. The type of display produced inside an OSD
box is, therefore, dependent on the states of the
TXT4.SHADOW ENABLE, TXT4.TRANS ENABLE,
TXT4.BMESH ENABLE and TXT4.CMESH ENABLE
register bits, as described previously. OSD boxes can only
be displayed in TV mode i.e. when the Picture On SFR bit
is a logic 1 and the Text On SFR bit is a logic 0, both inside
and outside text boxes and for both normal and
newsflash/subtitle pages.
The display of OSD boxes is not affected by the C7,
suppress header, and C10, inhibit display, control bits
stored in row 25 of the page memory.
9.15
Screen colour
The register bits TXT17.SCREEN COL2 to COL0 can be
used to define a colour to be displayed in place of TV
picture and the black background colour. If the bits are all
set to logic 0s, the screen colour is defined as ‘transparent’
and the TV picture and background colour are displayed
as normal.
Screen colour is displayed from 10.5 to 62.5
μ
s after the
active edge of the HSync input and on TV lines 23 to 310
inclusive, for a 625-line display, and lines 17 to 260
inclusive for a 525-line display.
When the screen colour has been redefined, no TV picture
is displayed so the FRAME de-interlace output can be
activated, if the SFR bits controlling FRAME are set up to
allow this.
Table 21
Screen colours
9.16
Redefinable Colours (SAA549x)
The CLUT SFR can be used to load a colour look-up table
(CLUT) which allows the 8 foreground colours and
8 background colours to be redefined. Each entry has
6 bits, 2 for each colour component, giving a total palette
of 64 colours from which to choose.
When the CLUT.CLUT ENABLE bit is a logic 0 the CLUT
is disabled and the device will display the normal, full
intensity, teletext colours.
The meaning of the least significant 6 bits of the CLUT
SFR depends on the setting of the CLUT.CLUT
ADDRESS bit when the register is written to. If the
CLUT.CLUT ADDRESS bit is a logic 1, the 4 LSB’s of the
SFR contain the address of the entry in the CLUT which
will be modified by subsequent writes to the CLUT SFR. If
the CLUT.CLUT ADDRESS bit is a logic 0, the 6 LSB’s of
the SFR define a colour which will be written into the CLUT
at the address defined by a previous write to the CLUT
SFR. An entry is written into the CLUT whenever the CLUT
SFR is written to, unless the CLUT.CLUT ADDRESS bit is
set.
Table 22 shows which CLUT entry corresponds to which
full intensity colour. The contents of the CLUT are not reset
at power-up and should be defined by the software before
the CLUT is enabled.
SCREEN
COL 2
SCREEN
COL 1
SCREEN
COL 0
SCREEN
COLOUR
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
transparent
red
green
yellow
blue
magenta
cyan
white
相關PDF資料 |
PDF描述 |
|---|---|
| SAA5297AH | Economy teletext and TV microcontrollers |
| SAA5297APS | Economy teletext and TV microcontrollers |
| SAA5297H | Economy teletext and TV microcontrollers |
| SAA5297PS | Economy teletext and TV microcontrollers |
| SAA5491 | Economy teletext and TV microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA5297AH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Economy teletext and TV microcontrollers |
| SAA5297APS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Economy teletext and TV microcontrollers |
| SAA5297H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Economy teletext and TV microcontrollers |
| SAA5297PS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Economy teletext and TV microcontrollers |
| SAA5355 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip colour CRT controller FTFROM |
發布緊急采購，3分鐘左右您將得到回復。