- 您現在的位置：買賣IC網 > PDF目錄372108 > SAA1501T (NXP SEMICONDUCTORS) Battery charge level indicator PDF資料下載
參數資料
| 型號： | SAA1501T |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 電源管理 |
| 英文描述： | Battery charge level indicator |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封裝： | 7.50 MM, PLASTIC, SO-24 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 372K |
| 代理商： | SAA1501T |
December 1994
8
Philips Semiconductors
Objective specification
Battery charge level indicator
SAA1501T
Display decoder driver
The counters are used to output the battery charge
amount via a decoder and driver stage to the display
outputs L100, L80, L60, L40 and L20 to drive an LCD
screen or an LED bargraph. A 64 Hz (based on
f
osc
= 4 kHz) block signal at output BP (back plane) must
be connected to the back plane of the LCD bar. If pin BP
is connected to ground, the display outputs L20 to L100
will produce signals for an LED bargraph. Output signal
POL (power-on LED) indicates when the batteries are in
the charge mode. When the counter is not at its maximum
state, POL is on and flickers at 2 Hz (based on
f
osc
= 4 kHz) when the counter is at its maximum. The
waveforms illustrated in Fig.4 depict operation of the
monitor display. The outputs BLI (battery low indication),
BUZ (buzzer) and FULL indicate the extreme status
(empty or full) of the counters and the batteries. The
waveforms of the signals BLI and BUZ if one switches over
from BATLD to standby when BLI is active, are given in
Fig.4.
The BLI sequence is as follows. If during discharge the
charge state falls below 0%, the red BLI LED is turned on.
Changing mode from discharge to standby means that the
BLI LED and the buzzer (BUZ) are activated as indicated
in Fig.4. If after a 0% passing recharge is activated, the red
BLI LED is turned on again for as long as the counter
remains below 10%. Switch-over in the 0 to 10% range to
standby will activate BLI and BUZ again.
The LEDs of the LED bargraph are activated as a result of
each operational mode change, starting with a step-up
pattern. Step-up means that LEDs are activated
successively one after the other, in accordance with the
charge status each
1
8
s (based on f
osc
= 4 kHz). After the
step-up, the LEDs will be on for 8 s (based on
f
osc
= 4 kHz), except for the POCH mode, where the LEDs
will be on continuously to inform the user about the charge
state of the batteries. The LCD display is, apart from the
LED mode, always visible.
Figure 5 shows the legend for Fig.6. Figure 6 shows the
operation of the monitor display.
BUZ
Fig.4 BLI and buzzer timing.
相關PDF資料 |
PDF描述 |
|---|---|
| SAA1502ATS | Safety IC for Li-ion |
| SAA1504T | Safety IC(安全保護芯片) |
| SAA1575HL | Global Positioning System (GPS)baseband processor(通用定位系統基帶處理器) |
| SAA2023GP | Drive processor for DCC systems |
| SAA2023 | Drive processor for DCC systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA1502ATS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Safety IC for Li-ion |
| SAA1504T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Safety IC |
| SA-A1520 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CRYSTAL CLOCK OSCILLATORS |
| SA-A1521 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CRYSTAL CLOCK OSCILLATORS |
| SA-A1527 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CRYSTAL CLOCK OSCILLATORS |
發布緊急采購，3分鐘左右您將得到回復。