- 您現在的位置：買賣IC網 > PDF目錄372106 > SA5775N (NXP SEMICONDUCTORS) Differential air core meter driver PDF資料下載
參數資料
| 型號： | SA5775N |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 其它接口 |
| 英文描述： | Differential air core meter driver |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PDIP16 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 111K |
| 代理商： | SA5775N |
Philips Semiconductors
Product specification
SA5775A
Differential air-core meter driver
1999 Sep 20
3
BLOCK DIAGRAM
8
9
10
12
13
14
15
16
1
2
3
4
5
7
6
3
LOGIC
DAC
MUX
SHUT–DOWN
LOGIC
11
SL00454
Figure 2. Block diagram
Table 1.
Pin #
1.
2.
3.
4.
5.
SA5775A Pin Descriptions for the N Package (Dual In-Line)
Name
SIN–
Negative output connection to the SIN coil of the gauge.
SIN+
Positive output connection to the SIN coil of the gauge.
A
GND
Ground for V
IGN
supply. Pins 3, 13 and 14 connected on the circuit board.
V
BB
Analog supply. Nominally 14.0 V.
DATA
OUT
Serial data output. Output of the internal shift register. When a new data word is shifted in, the old word is shifted out the
DATA
OUT
pin.
DATA
IN
Serial data input. A new data word is serially shifted into the part on the rising edge of S
CLK
. The data is shifted in MSB first.
V
CC
5 V logic supply. The internal latches and registers are set to zero on the rising edge of this signal.
OE
Output drivers are turned off when this input is low. Current draw is minimized.
S
CLK
Serial clock input. Data is loaded into the part on the rising edge of S
CLK
.
CS
Active high chip select input. When CS is high, the part is enabled to receive a new serial input word. The high-to-low tran-
sition of CS loads the new 10-bit word into the DAC registers and updates the output.
ST
Status output from this IC to indicate that the outputs have been disabled. The outputs may be disabled due to shorted out-
puts, over temperature conditions, power up reset, or output enable control pin .This output is an open drain output .Multiple
status outputs may be wire OR’ed together .This output is low when the outputs are disabled due to a fault condition.
nc
Not connected
D
GND
Ground for V
CC
supply. Connect to Pins 3 and 14.
A
GND
Ground for V
BB
supply. Connect to Pins 3 and 13.
COS–
Negative output connection to the COS coil of the gauge.
COS+
Positive output connection to the COS coil of the gauge.
Function
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
相關PDF資料 |
PDF描述 |
|---|---|
| SA5775A | Ceramic Multilayer Capacitor; Capacitance:82pF; Capacitance Tolerance:+/- 5 %; Working Voltage, DC:100V; Dielectric Characteristic:C0G/NP0; Package/Case:0603; Series:VJ; Leaded Process Compatible:Yes; Mounting Type:Surface Mount |
| SA5775AD | Differential air core meter driver |
| SA5775AN | Differential air core meter driver |
| SA5777A | Dual air-core gauge driver |
| SA5777AD | Dual air-core gauge driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA5777A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual air-core gauge driver |
| SA5777AD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual air-core gauge driver |
| SA5777AD,512 | 功能描述:馬達/運動/點火控制器和驅動器 DUAL DIFF AIRCORE METER DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| SA5777AD,518 | 功能描述:馬達/運動/點火控制器和驅動器 DUAL DIFF AIRCORE METER DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| SA5777AN | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual air-core gauge driver |
發布緊急采購，3分鐘左右您將得到回復。