參數資料
型號： S8233C
廠商： Seiko Instruments Inc.
英文描述： BATTERY PROTECTION IC FOR 3-SERIAL-CELL PACK
中文描述： 電池保護IC 3串行用電池
文件頁數： 13/26頁
文件大?。?/td> 568K
代理商： S8233C
Rev.4.0
_00
BATTERY PROTECTION IC FOR 3-SERIAL-CELL PACK
S-8233C Series
Seiko Instruments Inc.
13
Over discharge condition
If any one of the battery voltages falls below the over discharge detection voltage (V
DD
) during discharging
under normal condition and it continues for the over discharge detection delay time (t
DD
) or longer, the
discharging FET turns off and discharging stops. This condition is called the over discharge condition. In
this condition, output voltage of DSO goes ‘High’. When the discharging FET turns off, the VMP terminal
voltage becomes equal to the V
SS
voltage and the IC's current consumption falls below the power-down
current consumption (I
PDN
). This condition is called the power-down condition. The VMP and VSS
terminals are shorted by the R
VSM
resistor under the over discharge and power-down conditions.
The power-down condition is canceled when the charger is connected and the voltage between VMP and
VSS is 3.0 V or higher (over current detection voltage 3). When all the battery voltages becomes equal to
or higher than the over discharge release voltage (V
DU
) in this condition, the over discharge condition
changes to the normal condition. In this condition, output voltage of DSO goes ‘Low’.
Delay circuits
The over charge detection delay time (t
CU1
to t
CU3
), over discharge detection delay time (t
DD1
to t
DD3
), and
over current detection delay time 1 (t
IOV1
) are changed with external capacitors (C4 to C6).
The delay times are calculated by the following equations:
Min. Typ. Max.
t
CU
[s] =Delay factor ( 1.07, 2.13, 3.19)×C4 [uF]
t
DD
[s] =Delay factor ( 0.20, 0.40, 0.60)×C5 [uF]
t
IOV1
[s]=Delay factor ( 0.10, 0.20, 0.30)×C6 [uF]
Caution The delay time for over current detection 2 and 3 is fixed by an internal IC circuit. The
delay time cannot be changed via an external capacitor.
CTL terminal
If the CTL terminal is floated under normal condition, it is pulled up to the V
CC
potential in the IC, and both
the charging and discharging FETs turn off to inhibit charging and discharging. Both charging and
discharging are also inhibited by applying the VCC terminal to the CTL terminal externally. At this time,
the VMP and VCC terminals are shorted by the R
VCM
resistor.
When the CTL terminal becomes equal to V
SS
potential, charging and discharging are enabled and go
back to their appropriate conditions for the battery voltages.
Caution Please note unexpected behavior might occur when electrical potential difference
between the CTL pin ('L' level) and VSS is generated through the external filter
(R
VSS
and C
VSS
) as a result of input voltage fluctuations.
0 V battery charging function
This function is used to recharge the three serially-connected batteries after they self-discharge to 0 V.
When the 0 V charging start voltage (V
0CHAR
) or higher is applied to between VMP and VSS by connecting
the charger, the charging FET gate is fixed to V
SS
potential.
When the voltage between the gate sources of the charging FET becomes equal to or higher than the
turn-on voltage by the charger voltage, the charging FET turns on to start charging. At this time, the
discharging FET turns off and the charging current flows through the internal parasitic diode in the
discharging FET. If all the battery voltages become equal to or higher than the over discharge release
voltage (V
DU
), the normal condition returns.
CAUTION In the products without 0 V battery charging function, the resistance between VCC and
VMP and between VSS and VMP are lower than the products with 0 V battery charging
function. It causes to that over charge detection voltage increases by the drop voltage
of R5 (see Figure 8 for a connection example) with sink current at VMP.
The COP output is undefined below 2.0 V on VCC-VSS voltage in the products without
0 V battery charging function.
相關PDF資料
PDF描述
S82S09 576-BIT BIPOLAR RAM (64 X 9)
S82S19 576-BIT BIPOLAR RAM (64 X 9)
S82S212 2304 BIT BIPOLAR RAM
S8301 HD-SDI(High Definition Serial Digital Interface) Data Retimer(高分辨率串行數字接口重定時器)
S8423 BATTERY BACKUP IC
相關代理商/技術參數
參數描述
S-8233C 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:BATTERY PROTECTION IC FOR 3-SERIAL-CELL PACK
S-8233C_1 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:BATTERY PROTECTION IC FOR 3-SERIAL-CELL PACK
S-8233CAFT-TB 功能描述:電池管理 4.25V 3-Cell Serial RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
S-8233CAFT-TB-G 功能描述:電池管理 4.25V 3-Cell Serial RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
S82343 制造商:Intel 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*