- 您現在的位置：買賣IC網 > PDF目錄365430 > S6B1400X (SAMSUNG SEMICONDUCTOR CO. LTD.) 104 SEG / 65 COM DRIVER & CONTROLLER FOR STN LCD PDF資料下載
參數資料
| 型號： | S6B1400X |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 104 SEG / 65 COM DRIVER & CONTROLLER FOR STN LCD |
| 中文描述： | 104賽格/ 65 COM驅動程序 |
| 文件頁數： | 20/64頁 |
| 文件大?。?/td> | 445K |
| 代理商： | S6B1400X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
104 SEG / 65 COM DRIVER & CONTROLLER FOR STN LCD
SPEC. VER. 0.0 S6B1400X
16
3 Pin-SPI Interface (PS = "L", C68 = "L")
In 3-Pin SPI Interface mode, the pre-defined instruction called Display Data Length, is used to indicate whether
serial data input is display or instruction data instead of RS pin. The data is handled as instruction data until the
Display Data Length instruction is issued. This Display Data Length instruction consists of two bytes instruction. The
first byte instruction enables the next instruction to be valid, and the data of the second byte indicates that a
specified number of display data bytes (1 to 256) are to be transmitted. The next byte after the display data string is
handled as instruction data. For details, refers to figure 4.
SCLK
CS1B
/ CS2
829 830 831
~
~
0
0 1
7 8
~
15
~
23
SID
MSB
Data In
Page
LSB
DDC
No. of
DATA
3 Byte (1)
2 Byte (2)
104 Byte
0
(1) Set Page and Column Address.
Set Page Address
Set Column Address MSB
Set Column Address LSB
(2) Set DDC(Data Direction Command) and No. of Data Bytes.
Set Data Direction Command( For SPI mode Only):
: 1 0 1 1 P3 P2 P1 P0
: 0 0 0 1 0 Y6 Y5 Y4
: 0 0 0 0 Y3 Y2 Y1 Y0
1 0 0 0 0 0 0 0
: D7 D6 D5 D4 D3D2D1D0
Set No. of Data Bytes(DDL)
Figure 4. 3 Pin SPI Timing (RS is not used)
This command is used in 3-Pin SPI mode only. It will be two continuous commands, the first byte controls the data
direction and informs the LCD driver the second byte will be number of data bytes will be write. After these two
commands sending out, the following messages will be data. If data is stopped in transmitting, it is not valid data.
New data will be transferred serially with most significant bit first.
*NOTES:
- In spite of transmission of data, if CS1B will be disable, state terminates abnormally. Next state is initialized.
- The number of writing display data = DDL register value + 1
Busy Flag
The busy flag indicates whether the S6B1400X is operating or not. When DB7 is “H” in read status operation, this
device is in busy status and will accept only read status instruction. If the cycle time is correct, the microprocessor
needs not to check this flag before each instruction, which improves the MPU performance.
相關PDF資料 |
PDF描述 |
|---|---|
| S6B1713A05-B0CY | 65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B1713A05-B0CZ | 65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B1713A05-xxX0 | 65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B1713A05-xxXN | 65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B1713A15-B0CY | 65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S6B1713 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B1713A01-B0CY | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B1713A01-B0CZ | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B1713A01-XXX0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B1713A01-XXXN | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:65 COM / 132 SEG DRIVER & CONTROLLER FOR STN LCD |
發布緊急采購，3分鐘左右您將得到回復。