- 您現在的位置：買賣IC網 > PDF目錄365430 > S6A0093 (SAMSUNG SEMICONDUCTOR CO. LTD.) 80 SEG / 26 COM DRIVER & CONTROLLER FOR STN LCD PDF資料下載
參數資料
| 型號： | S6A0093 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 80 SEG / 26 COM DRIVER & CONTROLLER FOR STN LCD |
| 中文描述： | 80賽格/ 26 COM驅動程序 |
| 文件頁數： | 13/54頁 |
| 文件大?。?/td> | 594K |
| 代理商： | S6A0093 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
S6A0093
80 SEG / 26 COM DRIVER & CONTROLLER FOR STN LCD
10
Interface with MPU in Parallel Mode (PS = "High")
During writing operation, two 8-bit registers, data register (DR) and instruction register (IR), are used. The data
register (DR) is used as temporary data storage place for being written into DDRAM / CGRAM / ICONRAM and one
of these RAMs is selected by RAM address setting instruction. The Instruction register (IR) is used only to store
instruction code transferred from MPU. To select DR or IR register, RS input pin is used.
During reading operation, 8-bit register, output data register (OR) is used. The output data register (OR) is used as
temporary data storage place for being read from DDRAM / CGRAM / ICONRAM and one of these RAMs is selected
by RAM address setting instruction. After RAM address setting, first reading is a dummy cycle in 8-bit bus mode
(figure 3, 4). The valid data comes from second reading. In 4-bit bus mode, after RAM address setting, first and
second reading are dummy cycles (figure 5, 6). The valid data comes from third reading. The dummy read make the
address counter (AC) increased by 1. So it is recommended to set address again before writing. The instruction read
cycle is not supported and it is regarded as a no operation cycle.
In 4-bit bus mode, it is needed to transfer 4-bit data (through DB7
～
DB4) by two times. The high order bits (for 8-bit
mode DB7
～
DB4) are written before the low order bits (for 8-bit mode DB3
～
DB0) in write and low order bits (for 8-bit
mode DB3
～
DB0) are read before the high order bits (for 8-bit mode DB7
～
DB4) in read transaction. The DB0
～
DB3
pins are floated in this 4-bit bus mode. After RESETB resets, S6A0093 considers first 4-bit data from MPU as the
high order bits.
MI
CSB
RS
RW_WR
E_RD
DB7
～
DB0
Instruction
Write
Dummy
Read
Data
Write
NOP
RAM
Read
Valid
Data
IF
Figure 3. Timing Diagram of 8-bit Parallel Bus Mode Data Transfer (68-series MPU Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| S6A0094 | 80 SEG / 34 COM DRIVER & CONTROLLER FOR STN LCD |
| S6A2067 | 80 SEGMENT DRIVER FOR DOT MATRIX LCD |
| S6A2068 | 16COM/60SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD |
| S6B0715A01-B0CY | 33 COM / 100 SEG DRIVER & CONTROLLER FOR STN LCD |
| S6B0715A01-B0CZ | 33 COM / 100 SEG DRIVER & CONTROLLER FOR STN LCD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S6A0094 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:80 SEG / 34 COM DRIVER & CONTROLLER FOR STN LCD |
| S6A1-12VDC | 制造商:Allied Controls Incorporated 功能描述:Electromechanical Relay DPDT 2A 12VDC 160Ohm Through Hole |
| S6A1-24VDC | 制造商:Allied Controls Incorporated 功能描述: |
| S6A1-26.5VDC | 制造商:Allied Controls Incorporated 功能描述:Electromechanical Relay DPDT 2A 26.5VDC 700Ohm Through Hole |
| S6A13 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA Thyristor Silicon Planar Type |
發布緊急采購，3分鐘左右您將得到回復。