參數資料
型號: S5991-01
廠商: Electronic Theatre Controls, Inc.
英文描述: POSITION SENSITIVE DETECTOR
中文描述: 位置靈敏探測器
文件頁數: 11/16頁
文件大小: 1289K
代理商: S5991-01
8
The position detection error is usually measured with a
light beam of
φ
200 μm, so the specified areas shown in
Figures 4-4 to 4-6 are used for position detection error.
Figure 4-4
Specific area for one-dimensional PSD position
detection error (resistance length
12 mm)
OUTPUT
ELECTRODE
X
1
ACTIVE AREA
Position detection error for two-dimensional PSDs is sep-
arately measured in two areas: Zone A and Zone B. Two
zones are used because position detection error in the
circumference is larger than that in the center of the ac-
tive area,
·
Zone A: Within a circle with a diameter equal to 40 % of
one side length of the active area.
·
Zone B: Within a circle with a diameter equal to 80 % of
one side length of the active area.
Figure 4-5
Specific area for one-dimensional PSD position
detection error (resistance length > 12 mm)
OUTPUT
ELECTRODE
X
1
ACTIVE AREA
Figure 4-6 Specific area for two-dimensional PSD
position detection error
KPSDC0063EA
KPSDC0074EA
KPSDC0075EA
Figure 5-1 Basic connection example of one-dimensional
PSD and current-to-voltage conversion type
operational amplifier
KPSDC0076EA
Position resolution is the minimum detectable displace-
ment of a spot light incident on PSD, expressed as a dis-
tance on the PSD surface. Resolution is determined by the
PSD resistance length and the S/N. Using formula (1-6) as
an example, the following equation can be established.
B
+
x
L
X
In cases where the positional displacement is infinitely
small, the noise component contained in the output current
I
X2
clearly determines the position resolution. Generally, if
the PSD noise current is In, then the position resolution
R
is given as follows:
Figure 5-1 shows the basic connection example when us-
ing a PSD in conjunction with current-to-voltage amplifiers.
The noise model for this circuit is shown in Figure 5-2.
x: Small displacement
I: Change in output current
Then,
x can be expressed by the following equation.
I
X2
+
I = X
x =
L
X
. I
Io
R =
L
X
. In
Io
Characteristic and use
5. Position resolution
Io : Photocurrent
I
D
: Dark current
Rie: Interelectrode resistance
Cj : Junction capacitance
Rf : Feedback resistance
Cf : Feedback capacitance
en : Equivalent noise input voltage of operational amplifier
in : Equivalent noise input current of operational amplifier
Vo : Output voltage
KPSDC0077EA
Figure 5-2 Noise model
SPECIFIED RANGE
L
X
×
0.75
RESISTANCE LENGTH
L
X
OUTPUT
ELECTRODE
X
2
SPECIFIED RANGE
L
X
×
0.90
RESISTANCE LENGTH
L
X
OUTPUT
ELECTRODE
X
2
ACTIVE AREA
ZONE B
ZONE A
Rf
Cf
PSD
-
+
-
+
Rf
Cf
A
A
V
R
~
-
+
Rf
Cf
in
en
A
Vo
PSD
I
O
I
D
Rie
Cj
相關PDF資料
PDF描述
S5629 POSITION SENSITIVE DETECTOR
S5A 5.0 AMPS. Surface Mount Rectifiers
S5B 5.0 AMPS. Surface Mount Rectifiers
S5D 5.0 AMPS. Surface Mount Rectifiers
S5G 5.0 AMPS. Surface Mount Rectifiers
相關代理商/技術參數
參數描述
S599-90-068-11-071476 制造商:Mill-Max Mfg Corp 功能描述:
S5A 制造商:MCC 制造商全稱:Micro Commercial Components 功能描述:5 Amp Silicon Rectifier 50 to 1000 Volts
S5A R6 功能描述:整流器 5A 50V GLASS PASS SMD RECTIFIER RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
S5A R7 功能描述:整流器 5A 50V GLASS PASS SMD RECTIFIER RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
S5A/57T 功能描述:整流器 50 Volt 5.0 Amp 100 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel