- 您現在的位置：買賣IC網 > PDF目錄374665 > S3067 (Electronic Theatre Controls, Inc.) MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC PDF資料下載
參數資料
| 型號： | S3067 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC |
| 中文描述： | 多速率（OC-48/24/12/3/GBE/FC）的SONET / SDH / ATM的收發器瓦特/前向糾錯 |
| 文件頁數： | 7/27頁 |
| 文件大?。?/td> | 308K |
| 代理商： | S3067 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
7
S3067
MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC
September 17, 2002/ Revision A
Parallel-to-Serial Converter
The parallel-to-serial converter shown in Figure 4 is
comprised of a FIFO and a parallel-to-serial register.
The FIFO input latches the data from the PIN[15:0]
bus on the rising edge of PICLK. The parallel-to-
serial register is a loadable shift register which takes
its parallel input from the FIFO output.
An internally generated divide-by-16 clock, which is
phase aligned to the transmit serial clock as de-
scribed in the Timing Generatordescription, activates
the parallel data transfer between registers. The serial
data is shifted out of the parallel-to-serial register at
the TSCLK rate
.
FIFO
A FIFO is added to decouple the internal and exter-
nal (PICLK) clocks. The internally generated
divide-by-16 clock is used to clock out data from the
FIFO. PHINIT and LOCKDET are used to center or
reset the FIFO. The PHINIT and LOCKDET signals
will center the FIFO after the third PICLK pulse. This
is to insure that PICLK is stable. This scheme allows
the user to have an infinite PCLK-to-PICLK delay
through the ASIC. Once the FIFO is centered, the
PCLK-to-PICLK delay can have a maximum drift as
specified in Table 20.
FIFO Initialization
The FIFO can be initialized in one of the following
three ways:
1.
During power up, once the PLL has locked to
the reference clock provided on the REFCLK
pins, the LOCKDET will go active and initialize
the FIFO.
2.
When RSTB goes active, the entire chip is reset.
This causes the PLL to go out of lock and thus
the LOCKDET goes inactive. When the PLL re-
acquires the lock, the LOCKDET goes active
and initializes the FIFO. Note: PCLK is held re-
set when RSTB is active.
3.
The user can also initialize the FIFO by raising
PHINIT.
During the normal running operation, the incoming
data is passed from the PICLK timing domain to the
internally generated, divide-by-16 clock timing do-
main. Although the frequency of PICLK and the
internally generated clock is the same, their phase
relationship is arbitrary. To prevent errors caused by
short setup or hold times between the two timing
domains, the timing generator circuitry monitors the
phase relationship between PICLK and the internally
generated clock. When a potential setup or hold time
violation is detected, the phase error goes high.
When PHERR conditions occur, PHINIT should be
activated to recenter the FIFO (at least 2 PCLK peri-
ods). This can be done by connecting PHERR to
PHINIT. When realignment occurs, up to 10 bytes of
data will be lost. The user can also take in the
PHERR signal, process it and send an output to
PHINIT in such a way that idle bytes are lost during
the realignment process. PHERR will go inactive
when the realignment is complete.
Receiver Operation
The S3067 receiver chip provides the first stage of
digital processing of a receive SONET STS-48/STS-
24/STS-12/STS-3/GBE/FC bit-serial stream. The
bit-serial data stream is then converted into a 16-bit
half-word data format. A loopback mode is provided
for diagnostic loopback (transmitter to receiver). A line
loopback (receiver to transmitter) is also provided.
Both line and local loopback modes can be active at
the same time.
Serial-to-Parallel Converter
The serial-to-parallel converter consists of two 16-bit
registers. The first is a serial-in, parallel-out shift reg-
ister, which performs the serial-to-parallel conversion
clocked by the clock recovery block. On the falling
edge of the POCLK, the data in the parallel register
is transferred to an output parallel register which
drives POUT[15:0].
OTHER OPERATING MODES
Diagnostic Loopback
When the Diagnostic Loopback Enable (DLEB) input
is low, a loopback from the transmitter to the re-
ceiver at the serial data rate can be set up for
diagnostic purposes. The differential serial output
data from the transmitter is routed to the serial-to-
parallel block in place of the normal data stream
(RSD). TSD/TSCLK outputs are active. DLEB takes
precedence over SDPECL and SDTTL.
相關PDF資料 |
PDF描述 |
|---|---|
| S3067TB-156TBGA20 | MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC |
| S3067TB20 | MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC |
| S3063 | SONET/SDH/ATM OC-48 Differential 16:1 Transmitter(SONET/SDH/ATM差分16選1傳送器) |
| S3064 | SONET/SDH/ATM OC-48 Differential 1：16 Receiver(SONET/SDH/ATM差分1：16接收器) |
| S3067 | Multirate SONET/SDH/ATM Transceiver with FEC(帶正向糾錯功能的多速率SONET/SDH/ATM收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S3067TB-156TBGA20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC |
| S3067TB20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC |
| S30680 | 制造商:Microsemi Corporation 功能描述:800V 70A 2PIN DO-203AB - Bulk |
| S306AB | 制造商:Cinch Connectors 功能描述:Conn Wire to Board SKT 6 POS Solder Lug ST Panel Mount |
| S-306-AB | 功能描述:Jones 插頭和插槽 6C PNL MNT SOCKET RoHS:否 制造商:Molex 產品類型:Socket Connectors 系列:Beau 位置/觸點數量:8 電壓額定值:250 V 電流額定值:10 A 外殼材料:Thermoplastic 觸點材料:Phosphor Bronze 觸點電鍍:Tin-Lead |
發布緊急采購，3分鐘左右您將得到回復。