- 您現在的位置：買賣IC網 > PDF目錄365410 > S29PL127N80FFIW02 (Spansion Inc.) 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory PDF資料下載
參數資料
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
46
S29PL-N MirrorBit Flash Family
S29PL-N_00_A4 November 23, 2005
P r e l i m i n a r y
7.7
Hardware Reset
The RESET# input provides a hardware method of resetting the device to reading array data.
When RESET# is driven low for at least a period of t
RP
, the device immediately terminates any
operation in progress, tristates all outputs, and ignores all read/write commands for the duration
of the RESET# pulse. The device also resets the internal state machine to reading array data.
To ensure data integrity the operation that was interrupted should be reinitiated once the device
is ready to accept another command sequence.
When RESET# is held at V
SS
, the device draws CMOS standby current (I
CC4
). If RESET# is held
at V
IL
, but not at V
SS
, the standby current is greater.
RESET# may be tied to the system reset circuitry which enables the system to read the boot-up
firmware from the Flash memory upon a system reset.
See
Figure 11.5
and
Figure 11.8
for timing diagrams.
7.8
Software Reset
Software reset is part of the command set (see
Table 12.1
) that also returns the device to array
read mode and must be used for the following conditions:
1.
2.
To exit Autoselect mode
To reset software when DQ5 goes high during write status operation that indicates program
or erase cycle was not successfully completed
To exit sector lock/unlock operation.
To return to erase-suspend-read mode if the device was previously in Erase Suspend mode.
To reset software after any aborted operations
3.
4.
5.
Note:
Base = Base Address.
The following is a C source code example of using the reset function. Refer to the
Spansion
Low Level Driver User’s Guide
(available on
www.amd.com
and
www.fujitsu.com
) for general
information on Spansion Flash memory software development guidelines.
/* Example: Reset (software reset of Flash state machine) */
*( (UINT16 *)base_addr + 0x000 ) = 0x00F0;
The following are additional points to consider when using the reset command:
This command resets the banks to the read and address bits are ignored.
Reset commands are ignored once erasure has begun until the operation is complete.
Once programming begins, the device ignores reset commands until the operation is com-
plete
The reset command may be written between the cycles in a program command sequence be-
fore programming begins (prior to the third cycle). This resets the bank to which the system
was writing to the read mode.
If the program command sequence is written to a bank that is in the Erase Suspend mode,
writing the reset command returns that bank to the erase-suspend-read mode.
The reset command may be also written during an Autoselect command sequence.
Software Functions and Sample Code
Table 7.19 Reset
(LLD Function = lld_ ResetCmd)
Cycle
Operation
Word Address
Data
Reset Command
Write
Base + xxxh
00F0h
相關PDF資料 |
PDF描述 |
|---|---|
| S29PL127N80FFIW03 | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| S29PL127N80FFW000 | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| S29PL127N80FFW002 | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| S29PL127N80FFW003 | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| S29PL127N80FFWW00 | 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29PL127N80FFIW03 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| S29PL127N80FFW000 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| S29PL127N80FFW002 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| S29PL127N80FFW003 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
| S29PL127N80FFWW00 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。