參數資料
        型號: S29PL-J65BAI010
        廠商: Spansion Inc.
        元件分類: DRAM
        英文描述: CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        中文描述: CMOS 3V電壓供電,同步讀/寫Flash存儲器并有增強VersatileIO控制
        文件頁數: 63/96頁
        文件大小: 827K
        代理商: S29PL-J65BAI010
        September 22, 2006 S29PL-J_00_A9
        S29PL-J
        61
        D a t a
        S h e e t
        ( A d v a n c e
        I n f o r m a t i o n )
        15.9
        Program Suspend/Program Resume Commands
        The Program Suspend command allows the system to interrupt an embedded programming operation so that
        data can read from any non-suspended sector. When the Program Suspend command is written during a
        programming process, the device halts the programming operation within t
        PSL
        (program suspend latency)
        and updates the status bits. Addresses are “don’t-cares” when writing the Program Suspend command. After
        the programming operation has been suspended, the system can read array data from any non-suspended
        sector. The Program Suspend command may also be issued during a programming operation while an erase
        is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend.
        If a read is needed from the Secured Silicon Sector area, then user must use the proper command
        sequences to enter and exit this region. The system may also write the autoselect command sequence when
        the device is in Program Suspend mode. The device allows reading autoselect codes in the suspended
        sectors, since the codes are not stored in the memory array. When the device exits the autoselect mode, the
        device reverts to Program Suspend mode, and is ready for another valid operation. See “Autoselect
        Command Sequence” for more information. After the Program Resume command is written, the device
        reverts to programming. The system can determine the status of the program operation using the DQ7 or
        DQ6 status bits, just as in the standard program operation. See “Write Operation Status” for more
        information. The system must write the Program Resume command (address bits are “don’t care”) to exit the
        Program Suspend mode and continue the programming operation. Further writes of the Program Resume
        command are ignored. Another Program Suspend command can be written after the device has resumed
        programming.
        15.10 Command Definitions Tables
        Table 15.1 on page 62
        contains the Memory Array Command Definitions.
        相關PDF資料
        PDF描述
        S29PL-J65BAI011 CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        S29PL-J65BAI012 CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        S29PL-J65BAI013 CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        S29PL-J65BAI020 CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        S29PL-J65BAI021 CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        相關代理商/技術參數
        參數描述
        S29PL-J65BAI011 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        S29PL-J65BAI012 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        S29PL-J65BAI013 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        S29PL-J65BAI020 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control
        S29PL-J65BAI021 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous-Read/Write Flash Memory with Enhanced VersatileIO Control