參數資料
型號： S29GL128N10FAIV12
廠商： Spansion Inc.
英文描述： 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
中文描述： 3.0伏只頁面模式閃存具有110納米MirrorBit⑩工藝技術
文件頁數： 55/100頁
文件大小： 952K
代理商： S29GL128N10FAIV12
S29GL-N_00_B3 October 13, 2006
S29GL-N MirrorBit Flash Family
53
D a t a S h e e t
Once the specified number of write buffer locations have been loaded, the system must then
write the Program Buffer to Flash command at the sector address. Any other address and data
combination aborts the Write Buffer Programming operation. The device then begins pro-
gramming. Data polling should be used while monitoring the last address location loaded into
the write buffer. DQ7, DQ6, DQ5, and DQ1 should be monitored to determine the device sta-
tus during Write Buffer Programming.
The write-buffer programming operation can be suspended using the standard program sus-
pend/resume commands. Upon successful completion of the Write Buffer Programming
operation, the device is ready to execute the next command.
The Write Buffer Programming Sequence can be aborted in the following ways:
Load a value that is greater than the page buffer size during the Number of Locations to
Program step.
Write to an address in a sector different than the one specified during the
Write-Buffer-Load command.
Write an Address/Data pair to a different write-buffer-page than the one selected by the
Starting Address during the write buffer data loading stage of the operation.
Write data other than the Confirm Command after the specified number of data load cy-
cles.
The abort condition is indicated by DQ1 = 1, DQ7 = DATA# (for the last address location
loaded), DQ6 = toggle, and DQ5= 0. A Write-to-Buffer-Abort Reset command sequence must
be written to reset the device for the next operation.
Write buffer programming is allowed in any sequence. Note that the Secured Silicon sector,
autoselect, and CFI functions are unavailable when a program operation is in progress. This
flash device is capable of handling multiple write buffer programming operations on the same
write buffer address range without intervening erases.
Any bit in a w rite buffer address
range cannot be programmed from
0
back to a
1
.
Attempting to do so may cause the
device to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation was
successful. However, a succeeding read shows that the data is still
0
. Only erase operations
can convert a
0
to a
1
.
Accelerated Program
The device offers accelerated program operations through the WP#/ACC pin. When the sys-
tem asserts V
HH
on the WP#/ACC pin, the device automatically enters the Unlock Bypass
mode. The system may then write the two-cycle Unlock Bypass program command sequence.
The device uses the higher voltage on the WP#/ACC pin to accelerate the operation.
Note that
the
WP#/
ACC pin must not be at V
HH
for operations other than accelerated programming, or
device damage may result. WP# has an internal pullup; when unconnected, WP# is at V
IH
.
Figure 2, on page 55
illustrates the algorithm for the program operation. Refer to the Erase
and Program Operations subsection of the
“AC Characteristics” section on page 77
for param-
eters, and
Figure 14, on page 81
for timing diagrams.
相關PDF資料
PDF描述
S29GL128N10FAIV13 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10FAIV20 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10FAIV22 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10FAIV23 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10FFI010 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
相關代理商/技術參數
參數描述
S29GL128N10FFI010 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 128Mbit 16M/8M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 128MB SMD 29LV128
S29GL128N10FFI020 制造商:Spansion 功能描述:Flash - NOR IC
S29GL128N10TF101 制造商:Spansion 功能描述:
S29GL128N10TFI010 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:128Mb （16M x 8，8M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91
S29GL128N10TFI020 制造商:Spansion 功能描述:S29GL128N10TFI020 制造商:Spansion 功能描述:Flash - NOR IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*