- 您現在的位置：買賣IC網 > PDF目錄385801 > S29GL128M90TDIR22 (SPANSION LLC) 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology PDF資料下載
參數資料
| 型號： | S29GL128M90TDIR22 |
| 廠商： | SPANSION LLC |
| 元件分類： | DRAM |
| 英文描述： | 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
| 中文描述： | 8M X 16 FLASH 3V PROM, 90 ns, PDSO56 |
| 封裝： | LEAD FREE, TSOP-56 |
| 文件頁數： | 115/160頁 |
| 文件大?。?/td> | 2142K |
| 代理商： | S29GL128M90TDIR22 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁當前第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
April 30, 2004 S29GLxxxM_00A5
S29GLxxxM MirrorBit
TM
Flash Family
115
P r e l i m i n a r y
Write Operation Status
The device provides several bits to determine the status of a program or erase
operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 19 and the following subsec-
tions describe the function of these bits. DQ7 and DQ6 each offer a method for
determining whether a program or erase operation is complete or in progress.
The device also provides a hardware-based output signal, RY/BY#, to determine
whether an Embedded Program or Erase operation is in progress or has been
completed.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded
Program or Erase algorithm is in progress or completed, or whether the device is
in Erase Suspend. Data# Polling is valid after the rising edge of the final WE#
pulse in the command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the com-
plement of the datum programmed to DQ7. This DQ7 status also applies to
programming during Erase Suspend. When the Embedded Program algorithm is
complete, the device outputs the datum programmed to DQ7. The system must
provide the program address to read valid status information on DQ7. If a pro-
gram address falls within a protected sector, Data# Polling on DQ7 is active for
approximately 1 μs, then the device returns to the read mode.
During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7.
When the Embedded Erase algorithm is complete, or if the device enters the
Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must
provide an address within any of the sectors selected for erasure to read valid
status information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing
are protected, Data# Polling on DQ7 is active for approximately 100 μs, then the
device returns to the read mode. If not all selected sectors are protected, the Em-
bedded Erase algorithm erases the unprotected sectors, and ignores the selected
sectors that are protected. However, if the system reads DQ7 at an address within
a protected sector, the status may not be valid.
Just prior to the completion of an Embedded Program or Erase operation, DQ7
may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is as-
serted low. That is, the device may change from providing status information to
valid data on DQ7. Depending on when the system samples the DQ7 output, it
may read the status or valid data. Even if the device has completed the program
or erase operation and DQ7 has valid data, the data outputs on DQ0–DQ6 may
be still invalid. Valid data on DQ0–DQ7 will appear on successive read cycles.
Table
33
shows the outputs for Data# Polling on DQ7. Figure 7 shows the Data#
Polling algorithm. Figure 17 in the AC Characteristics section shows the Data#
Polling timing diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL128M90TDIR23 | 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
| S29GL128M90TDIR80 | 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
| S29GL128M90TDIR82 | 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
| S29GL128M90TDIR83 | 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
| S29GL128M90TFIR10 | 3.0 Volt-only Page Mode Flash Memory featuring 0.23 um MirrorBit process technology |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL128M90TFIR10 | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 128M-Bit 16M x 8/8M x 16 90ns 56-Pin TSOP Tray |
| S29GL128N10FFI010 | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 128Mbit 16M/8M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 128MB SMD 29LV128 |
| S29GL128N10FFI020 | 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL128N10TF101 | 制造商:Spansion 功能描述: |
| S29GL128N10TFI010 | 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:128Mb （16M x 8，8M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91 |
發布緊急采購，3分鐘左右您將得到回復。