參數資料
型號： S29GL032M10BCIR43
廠商： SPANSION LLC
元件分類： PROM
英文描述： MirrorBit Flash Family
中文描述： 2M X 16 FLASH 3V PROM, 100 ns, PBGA48
封裝： LEAD FREE, BGA-48
文件頁數： 20/162頁
文件大?。?/td> 4557K
代理商： S29GL032M10BCIR43
116
S29GLxxxM MirrorBitTM Flash Family
S29GLxxxM_00A4 March 30, 2004
Pr e l i m i n a r y
Write Operation Status
The device provides several bits to determine the status of a program or erase
operation: DQ2, DQ3, DQ5, DQ6, and DQ7. Table 19 and the following subsec-
tions describe the function of these bits. DQ7 and DQ6 each offer a method for
determining whether a program or erase operation is complete or in progress.
The device also provides a hardware-based output signal, RY/BY#, to determine
whether an Embedded Program or Erase operation is in progress or has been
completed.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded
Program or Erase algorithm is in progress or completed, or whether the device is
in Erase Suspend. Data# Polling is valid after the rising edge of the final WE#
pulse in the command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the com-
plement of the datum programmed to DQ7. This DQ7 status also applies to
programming during Erase Suspend. When the Embedded Program algorithm is
complete, the device outputs the datum programmed to DQ7. The system must
provide the program address to read valid status information on DQ7. If a pro-
gram address falls within a protected sector, Data# Polling on DQ7 is active for
approximately 1 s, then the device returns to the read mode.
During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7.
When the Embedded Erase algorithm is complete, or if the device enters the
Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must
provide an address within any of the sectors selected for erasure to read valid
status information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing
are protected, Data# Polling on DQ7 is active for approximately 100 s, then the
device returns to the read mode. If not all selected sectors are protected, the Em-
bedded Erase algorithm erases the unprotected sectors, and ignores the selected
sectors that are protected. However, if the system reads DQ7 at an address within
a protected sector, the status may not be valid.
Just prior to the completion of an Embedded Program or Erase operation, DQ7
may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is as-
serted low. That is, the device may change from providing status information to
valid data on DQ7. Depending on when the system samples the DQ7 output, it
may read the status or valid data. Even if the device has completed the program
or erase operation and DQ7 has valid data, the data outputs on DQ0–DQ6 may
be still invalid. Valid data on DQ0–DQ7 will appear on successive read cycles.
Table 33 shows the outputs for Data# Polling on DQ7. Figure 7 shows the Data#
Polling algorithm. Figure 17 in the AC Characteristics section shows the Data#
Polling timing diagram.
相關PDF資料
PDF描述
S29GL256N10FAI010 MirrorBit Flash Family
S29GL256N10FFI010 MirrorBit Flash Family
S29GL256N80FAI010 MirrorBit Flash Family
S29GL256N80FFI010 MirrorBit Flash Family
S29GL256N80FFI013 MirrorBit Flash Family
相關代理商/技術參數
參數描述
S29GL032M10BCIR50 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10BCIR52 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10BCIR53 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10BCIR60 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
S29GL032M10BCIR62 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*