- 您現在的位置：買賣IC網 > PDF目錄374647 > S216S02 (Sharp Corporation) IT(rms)÷16A, Zero Cross type SIP 4pin Triac output SSR PDF資料下載
參數資料
| 型號： | S216S02 |
| 廠商： | Sharp Corporation |
| 英文描述： | IT(rms)÷16A, Zero Cross type SIP 4pin Triac output SSR |
| 中文描述： | 資訊科技（有效值）÷ 16A條，零交叉式園區4芯晶閘管輸出蘇維埃社會主義共和國 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 242K |
| 代理商： | S216S02 |
8
S116S02 Series
S216S02 Series
■
Design Considerations
●
Recommended Operating Conditions
Parameter
Input signal current at ON state
Input signal current at OFF state
In order for the SSR to turn off, the triggering current (l
F
) must be 0.1mA or less.
When the input current (I
F
) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, V
D
, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit vales to start with : Cs=0.1
μ
F and Rs=47
. The operation of the SSR and
snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit com-
ponent values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenoids.
Following the procedure outlined above should provide sufficient results.
For over voltage protection, a Varistor may be used.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main out-
put triac as possible.
Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry.
If the phase difference between the voltage and the current at the output pins is large enough, zero crossing
type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR
may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should
be used in combination with the above mentioned snubber circuit selection process.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5Nm.
In order to dissipate the heat generated from the inside of device effectively, please follow the below sugges-
tions.
●
Design guide
Sheet No.: D4-A02701EN
S116S02
S216S02
Symbol
I
F
(ON)
I
F
(OFF)
Unit
mA
mA
Input
Output
Load supply voltage
Load supply current
Frequency
Operating temperature
V
OUT
(rms)
I
OUT
(rms)
f
T
opr
V
mA
Hz
C
Locate snubber circuit between output terminals
(Cs
=
0.1
μ
F, Rs
=
47
)
Conditions
16
0
80
80
0.1
47
20
24
0.1
120
240
I
T
(rms)
×
80%(
)
63
80
MIN.
MAX.
(
) See Fig.2 about derating curve (I
T
(rms) vs. ambient temperature).
相關PDF資料 |
PDF描述 |
|---|---|
| S216S02F | IT(rms)÷16A, Zero Cross type SIP 4pin Triac output SSR |
| S21MA01 | 6-pin DIP Type SSR for Low Power Control |
| S21MD10T | High Speed, High Sensitivity Type Phototriac Coupler |
| S21MD3 | High Noise Resistance Type Phototriac Coupler |
| S21MD3TV | High Noise-resistance Type Phototriac Coupler |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S216S02F | 功能描述:固態繼電器-PCB安裝 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| S216SE1 | 功能描述:RELAY SSR 240VAC 16A TRIAC 4-SIP RoHS:否 類別:繼電器 >> 固態 系列:S216 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO（1 Form A） 輸出類型:AC，DC（RF） 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD（SMT）接片 封裝/外殼:4-SMD（0.175"，4.45mm） 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6 |
| S216SE1F | 功能描述:固態繼電器-PCB安裝 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| S216SE2 | 功能描述:RELAY SSR 240VAC 16A ZC 4-SIP RoHS:否 類別:繼電器 >> 固態 系列:S216 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO（1 Form A） 輸出類型:AC，DC（RF） 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD（SMT）接片 封裝/外殼:4-SMD（0.175"，4.45mm） 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6 |
| S216SE2F | 功能描述:固態繼電器-PCB安裝 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。