- 您現在的位置：買賣IC網 > PDF目錄98069 > S202SE2 (SHARP ELECTRONICS CORP) TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX PDF資料下載
參數資料
| 型號： | S202SE2 |
| 廠商： | SHARP ELECTRONICS CORP |
| 元件分類： | 繼電器，輸入/輸出模塊 |
| 英文描述： | TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX |
| 封裝： | PLASTIC, SIP-4 |
| 文件頁數： | 14/14頁 |
| 文件大小： | 244K |
| 代理商： | S202SE2 |
9
S202SE2 Series
Sheet No.: D4-A03301EN
(a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface.
(b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device
surface.
(c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface.
Silicone grease to be used is as follows;
1) There is no aged deterioration within the operating temperature ranges.
2) Base oil of grease is hardly separated and is hardly permeated in the device.
3) Even if base oil is separated and permeated in the device, it should not degrade the function of a device.
Recommended grease : G-746 (Shin-Etsu Chemical Co., Ltd.)
: G-747 (Shin-Etsu Chemical Co., Ltd.)
: SC102 (Dow Corning Toray Silicone Co., Ltd.)
In case the optional heat sink is screwed up, please solder after screwed.
In case of the lead frame bending, please keep the following minimum distance and avoid any mechanical
stress between the base of terminals and the molding resin.
Some of AC electromagnetic counters or solenoids have built-in rectifier such as the diode.
In this case, please use the device carefully since the load current waveform becomes similar with
rectangular waveform and this results may not make a device turn off.
Example how to equip optional heat sink for reinforced isolation
1) Case of isolation sheet whose thickness is 0.4mm or more (Viso : 3kV or more)
2) Case of the use of double isolation sheet (Viso : each 3kV or more)
Please keep 5mm distance as minimum between naked metal portion of SSR and heat sink, and also
between naked metal portion of SSR and bis/nut/washer.
However, please avoid the natural rubber for isolation sheet.
4.4mm MIN.
Heat sink
SSR
0.4mm thickness or more
isolation sheet
Heat sink
SSR
Isolation sheet
相關PDF資料 |
PDF描述 |
|---|---|
| S3C1850XX-SM | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| S3C3410XXX-QA | 32-BIT, MROM, 40 MHz, RISC MICROCONTROLLER, PQFP128 |
| S3C70F2XX-SO | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO32 |
| S3C70F4XX-AV | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP30 |
| S3C72M9XX-QA | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP128 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S202SE2F | 功能描述:固態繼電器-PCB安裝 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| S-202T | 功能描述:穩流二極管 100V 2mA RoHS:否 制造商:Central Semiconductor 最大調節器電流:5.17 mA 最大極限電壓:2.9 V 最大峰值工作電壓:100 V 安裝風格:Through Hole 封裝 / 箱體:DO-204AH 封裝: |
| S202T01 | 功能描述:RELAY SSR 240VAC 2A TRIAC 4-SIP RoHS:否 類別:繼電器 >> 固態 系列:S202 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO（1 Form A） 輸出類型:AC，DC（RF） 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD（SMT）接片 封裝/外殼:4-SMD（0.175"，4.45mm） 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6 |
| S202T01F | 功能描述:固態繼電器-PCB安裝 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| S202T02 | 功能描述:RELAY SSR 240VAC 2A ZC 4-SIP RoHS:否 類別:繼電器 >> 固態 系列:S202 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO（1 Form A） 輸出類型:AC，DC（RF） 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD（SMT）接片 封裝/外殼:4-SMD（0.175"，4.45mm） 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6 |
發布緊急采購，3分鐘左右您將得到回復。