- 您現在的位置：買賣IC網 > PDF目錄368610 > S1M8662AX01-F0T0 (SAMSUNG SEMICONDUCTOR CO. LTD.) CDMA/PCS/GPS Triple Mode IF/ baseband IC PDF資料下載
參數資料
| 型號： | S1M8662AX01-F0T0 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | CDMA/PCS/GPS Triple Mode IF/ baseband IC |
| 中文描述： | 碼分多址/件/全球定位系統三模式中頻/基帶IC |
| 文件頁數： | 11/22頁 |
| 文件大?。?/td> | 175K |
| 代理商： | S1M8662AX01-F0T0 |
RX IF/BBA WITH GPS
S1M8662A (Preliminary)
11
FUNCTIONAL DESCRIPTION
S1M8662A is a CDMA/GPS receive-only baseband analog IC, located between the RF mid-frequency processing
terminal and baseband processing terminal. The RF analog mid-frequency signal terminal(IF SAW filter output),
directly connected to the S1M8662A mid-frequency input pin, converts and processes the baseband signal and
sends the corresponding digital signal to the modem IC. Baseband analog processing uses QPSK modulation,
LPF, and A-D converter and the modem IC performs digital CDMA /GPS baseband modulation on the digitalized
analog baseband signal it receives. An on-chip VCO creates a multiple frequency(x2, x3, x4, x6) LO signal.
S1M8662A uses a 0.5um BiCMOS, equipped with high-frequency bipolar and low power standardized CMOS
logic, to operate safely in the low power range, consisting of power voltage between 2.7 to 3.3V and operating
temperature between -30 to +85
°
C.
CDMA Receive Signal Path
The receive circuit of S1M8662A has the Rx AGC, an automatic gain controller, and baseband LPF and output
terminal with the A-D converter, and VCO and mixer etc. The input signal is received as a differential signal,
which is modulated to 1.23 MHz spread-spectrum for CDMA. The mid-frequency is 220.38MHz for Korea-PCS,
1.23MHz for US-PCS, and 85.38MHz for cellular; they are set based on the time constants of the components
involved with the external VCO and external Rx PLL. Rx AGC , connected to both the IF SAW filter and
matching component in the RF-IF converter output located in the RF block, amplifies or reduces according to the
signal size. It takes its orders from the modem chip when it sets the appropriate receive level as required by the
CDMA system. Gain is controlled by applying a DC voltage to the RAGC_CONT pin. The applied DC is produced
when the PDM signal, generated as a control signal in the modem, passes through the R-C filter. The control
band of this AGC is approx. 90dB. The QPSK Baseband modulator separates and modulates the IF signal sent
by the AGC using I(In-phase) and Q(Quad-phase) baseband signal. Essentially, two signals, I-LO and Q-LO
(Local oscillator), are mixed with AGC's IF output signals, respectively. The LO(local oscillator) signal is
generated by the internal oscillating components, externally connected tank coil, and Varactor, and the externally
independent PLL device is used to generate its exact oscillation mid-frequency.
T=0
Q-CH
I-CH
Figure 4. Received I/Q Phase in S1M8662A
Defining of the I-Phase and Q-Phase receive path is very important to its design. The polarities of these paths
are also important to digital baseband modulation. Therefore, the output of the QPSK baseband modulation
determines the I and Q phases; I-phase is defined as the phase leading the Q-phase by exactly 90
°
, but it simpler
to think of I as Cosin and Q as Sin. The figure related to this is shown in Figure 5. This definition is valid only
when the QPSK IF input signal is higher than the IF mid-frequency. The baseband signal, output by the QPSK
modulator, includes various other unnecessary surrounding band noises, which are removed by the use of the
LPF(Low-Pass-Filter).
Ultimately, I and Q filtered signals are converted to digital signals by the 4-bit A-D converter and sent to the
modem. The A-D converter used is a parallel output type and its outputs are synchronized at the CHIP
×
8 rising
edge. The modem chip captures the data on the CHIP
×
8 falling edge. The CHIP
×
8 clock used in the A-D
converter received to MSM.
相關PDF資料 |
PDF描述 |
|---|---|
| S1M8836 | FRACTIONAL-N RF/INTEGER-N IF DUAL PLL |
| S1M8836X01-G0T0 | FRACTIONAL-N RF/INTEGER-N IF DUAL PLL |
| S1M8837 | FRACTIONAL-N RF/INTEGER-N IF DUAL PLL |
| S1M8837X01-G0T0 | FRACTIONAL-N RF/INTEGER-N IF DUAL PLL |
| S1PG | High Current Density Surface Mount Glass-Passivated Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1M8821 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:INTERGER RF/IF DUAL PLL |
| S1M8821X01-R0T0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:INTERGER RF/IF DUAL PLL |
| S1M8822 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:INTERGER RF/IF DUAL PLL |
| S1M8822X01-R0T0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:INTERGER RF/IF DUAL PLL |
| S1M8823 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:INTERGER RF/IF DUAL PLL |
發布緊急采購，3分鐘左右您將得到回復。