參數資料
型號： S1D2500A01-D0B0
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
元件分類： 視頻放大器
英文描述： I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER
中文描述： 的I2C總線控制轉/克/乙視頻放大器
文件頁數： 14/27頁
文件大小： 210K
代理商： S1D2500A01-D0B0
S1D2500A01 I
2
C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS
14
NOTES:
1.
2.
For guaranteed specifications and test conditions, See the Electrical Characteristics. The guaranteed specifications apply
only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under
the listed test conditions.
3.
V
CC
supply pins 6, 9, and 23 must be externally wired together to prevent internal damage during V
CC
power on/off
cycles.
4.
The supply current specified is the quiescent current for V
CC1
/V
CC2
and V
CC3
with RL =
￥
. The supply current
for V
CC3
(pin 23) also depends on the output load.
5.
Output voltage is dependent on load resistor. Test circuit uses RL = 390
6.
Measure gain difference between any two amplifiers Vin = 560mVpp.
7.
When measuring video amplifier bandwidth or pulse rise and fall times, a double sided full ground plane printed circuit
board without socket is recommended. Video amplifier 10MHz isolation test also requires this printed circuit board.
The reason for a double sided full ground plane PCB is that large measurement variations occur in single sided PCBs.
8.
Adjust input frequency from 10MHz (AV max reference level) to the-3dB frequency (f -3dB).
9.
Measure output levels of the other two undriven amplifiers relative to the driven amplifier to determine channel separation.
Terminate the undriven amplifier inputs to simulate generator loading. Repeat test at fin = 10MHz for Iso_10MHz.
10. A minimum pulse width of 200 ns is guaranteed for a horizontal line of 15kHz. This limit is guaranteed by design. if a lower
line rate is used a longer clamp pulse may be required.
11. During the AC test the 4V DC level is the center voltage of the AC output signal. For example. if the output is 4Vpp the
signal will swing between 2V DC and 6V DC.
12. These parameters are not tested on each product which is controlled by an internal qualification procedure.
Absolute Maximum Rating Indicates the limit beyond which damage to the device may occur.
Operating Ratings indicate conditions for which the device is functional but do not guarantee specific performance limits.
相關PDF資料
PDF描述
S1D2500A01-D0 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER
S1D2500A WIDE BAND ANALOG SWITCH FOR MONITORS
S1D2507B WIDE BAND ANALOG SWITCH FOR MONITORS
S1D2507B01 Circular Connector; MIL SPEC:MIL-C-26482, Series I, Solder; Body Material:Aluminum; Series:PT08; No. of Contacts:36; Connector Shell Size:22; Connecting Termination:Solder; Circular Shell Style:Right Angle Plug
S1D2502A01-D0B0 MLH Series All Metal Pressure Sensor, Gage, Amplified, 0 psi to 250 psi Pressure Range, 1/8-27 NPT Port Style, 1 Vdc to 5 Vdc Output Type, Packard MetriPak Termination Type
相關代理商/技術參數
參數描述
S1D2502A01-D0B0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2502B01-D0B0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
S1D2503X01-D0B0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS
S1D2504A01 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*