參數資料
型號： S1D13305F00A
元件分類： 顯示控制器
英文描述： 640 X 256 PIXELS CRT CHAR OR GRPH DSPL CTLR, PQFP60
封裝： QFP5-60
文件頁數： 27/94頁
文件大?。?/td> 541K
代理商： S1D13305F00A
S1D13305 Series
EPSON
27
Technical Manual
8.2.1.13. AP
Defines the horizontal address range of the virtual screen.
APL is the least significant byte of the address.
Figure 8. AP and C/R relationship
8.2.2. SLEEP IN
Places the system in standby mode. This command has no
parameter bytes. At least one blank frame after receiving
this command, the S1D13305F halts all internal opera-
tions, including the oscillator, and enters the sleep state.
Figure 7. AP parameters
APL
AP7
AP6
AP5
AP4
AP3
AP2
AP1
AP0
APH
AP15
AP14
AP13
AP12
AP11
AP10
AP9
AP8
Table 8. Horizontal address range
Hex code
[AP] addresses
APH
APL
per line
0000
0
0001
1
↓↓↓↓
↓
0050
80
↓↓↓↓
↓
FFFE
216 – 2
FFFF
216 – 1
Display area
C/R
Display memory limit
AP
Blank data is sent to the X-drivers, and the Y-drivers have
their bias supplies turned off by the YDIS signal. Using
the YDIS signal to disable the Y-drivers guards against
any spurious displays.
The internal registers of the S1D13305 series maintain
their values during the sleep state. The display memory
control pins maintain their logic levels to ensure that the
display memory is not corrupted.
The S1D13305 series can be removed from the sleep state
by sending the SYSTEM SET command with only the P1
parameter. The DISP ON command should be sent next
to enable the display.
Figure 9. SLEEP IN instruction
1. The YDIS signal goes LOW between one and two
frames after the SLEEP IN command is received.
Since YDIS forces all display driver outputs to go to
the deselected output voltage, YDIS can be used as a
power-down signal for the LCD unit. This can be
done by having YDIS turn off the relatively high-
power LCD drive supplies at the same time as it
blanks the display.
2. Since all internal clocks in the S1D13305 series are
halted while in the sleep state, a DC voltage will be
applied to the LCD panel if the LCD drive supplies
remain on.
If reliability is a prime consideration, turn off the
LCD drive supplies before issuing the SLEEP IN
command.
3. Note that, although the bus lines become high imped-
ance in the sleep state, pull-up or pull-down resistors
on the bus will force these lines to a known state.
MSB
LSB
C
0
1
01001
1
INSTRUCTION SET
相關PDF資料
PDF描述
S1D13600F00A CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
S1D13700F02A100 320 X 240 PIXELS CRT OR FLAT PNL GRPH DSPL CTLR, PQFP64
S1D13706F00A 320 X 240 PIXELS CRT OR FLAT PNL GRPH DSPL CTLR, PQFP100
S1D13806F00A CRT OR FLAT PNL GRPH DSPL CTLR, PQFP144
S1D13A05B00B 320 X 320 PIXELS CRT OR FLAT PNL GRPH DSPL CTLR, PBGA121
相關代理商/技術參數
參數描述
S1D13305F00A100 制造商:SEIKO 功能描述:
S1D13305F00A200 制造商:Epson Electronics America Inc 功能描述:Access Mls Drive Method Lcd Chp Set
S1D13305F00B 制造商:EPSON 制造商全稱:EPSON 功能描述:LCD Controller ICs
S1D13305F00B100 制造商:Epson Electronics America Inc 功能描述:LCD DRVR 3V/3.3V/5V 80-Pin TQFP
S1D13501F00A100 制造商:Epson Electronics America Inc 功能描述:LCD DRVR 3V/3.3V/5V 80-Pin TQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*