參數資料
型號： S12MEBIV3
廠商： Motorola, Inc.
英文描述： MC9S12DT128 Device User Guide V02.09
中文描述： MC9S12DT128設備的用戶手冊V02.09
文件頁數： 21/138頁
文件大小： 2083K
代理商： S12MEBIV3
MC9S12DT128 Device User Guide — V02.09
21
–
The Byteflight pin functionality (BF_PSLM, BF_PERR, BF_PROK, BF_PSYN, TX_BF,
RX_BF) is not available on port PM7, PM6, PM5, PM4, PM3 and PM2, if using a derivative
without Byteflight (see
Table 0-1
).
–
Do not write MODRR1 and MODRR0 Bit of Module Routing Register (PIM_9DTB128 Block
User Guide), if using a derivative without CAN0 (see
Table 0-1
).
–
Do not write MODRR3 and MODRR2 Bit of Module Routing Register (PIM_9DTB128 Block
User Guide), if using a derivative without CAN4 (see
Table 0-1
).
Pins not available in 80 pin QFP package for
MC9S12DG128E, MC9S12DG128,
MC9S12DJ128E, and MC9S12DJ128
Port H
In order to avoid floating nodes the ports should be either configured as outputs by setting the
data direction register (DDRH at Base+$0262) to $FF, or enabling the pull resistors by writing
a $FF to the pull enable register (PERH at Base+$0264).
–
–
Port J[1:0]
PortJpull-upresistorsareenabledoutofresetonallfourpins(7:6and1:0).Thereforecaremust
be taken not to disable the pull enables on PJ[1:0] by clearing the bits PERJ1 and PERJ0 at
Base+$026C.
–
Port K
Port K pull-up resistors are enabled out of reset, i.e. Bit 7 = PUKE = 1 in the register PUCR at
Base+$000C. Therefore care must be taken not to clear this bit.
–
Port M[7:6]
PM7:6 must be configured as outputs or their pull resistors must be enabled to avoid floating
inputs.
–
Port P6
PP6 must be configured as output or its pull resistor must be enabled to avoid a floating input.
–
Port S[7:4]
PS7:4 must be configured as outputs or their pull resistors must be enabled to avoid floating
inputs.
–
PAD[15:8] (ATD1 channels)
OutofresettheATD1isdisabledpreventingcurrentflowsinthepins.DonotmodifytheATD1
registers!
Pins not available in 80 pin QFP package for
MC9S12DB128
Port H
In order to avoid floating nodes the ports should be either configured as outputs by setting the
data direction register (DDRH at Base+$0262) to $FF, or enabling the pull resistors by writing
a $FF to the pull enable register (PERH at Base+$0264).
–
–
Port J[7:6, 1:0]
PortJpull-upresistorsareenabledoutofresetonallfourpins(7:6and1:0).Thereforecaremust
be taken not to disable the pull enables on PJ[7:6, 1:0] by clearing the bits PERJ7, PERJ6,
PERJ1 and PERJ0 at Base+$026C.
相關PDF資料
PDF描述
S12MEBIV3D MC9S12DT128 Device User Guide V02.09
S12SCIV2 MC9S12DT128 Device User Guide V02.09
S12SCIV2D MC9S12DT128 Device User Guide V02.09
S12VREGV1 MC9S12DT128 Device User Guide V02.09
S12VREGV1D MC9S12DT128 Device User Guide V02.09
相關代理商/技術參數
參數描述
S12MEBIV3D 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MC9S12DT128 Device User Guide V02.09
S12MMCV4 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MC9S12DT128 Device User Guide V02.09
S12MMCV4D 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MC9S12DT128 Device User Guide V02.09
S12MR 功能描述:整流器 1000V 12A REV Leads Std. Recovery RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
S12MSCANV2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MC9S12DT128 Device User Guide V02.09
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*