- 您現在的位置：買賣IC網 > PDF目錄299876 > S-T111B23MC-OGI-TF 2.3 V FIXED POSITIVE LDO REGULATOR, PDSO5 PDF資料下載
參數資料
| 型號： | S-T111B23MC-OGI-TF |
| 元件分類： | 固定正電壓單路輸出LDO穩壓器 |
| 英文描述： | 2.3 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
| 封裝： | SOT-23, 5 PIN |
| 文件頁數： | 5/23頁 |
| 文件大?。?/td> | 282K |
| 代理商： | S-T111B23MC-OGI-TF |
HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR
Rev.1.3_00
S-T111 Series
Seiko Instruments Inc.
13
Precautions
Wiring patterns for the VIN, VOUT and GND pins should be designed so that the impedance is low.
When mounting an output capacitor between the VOUT and VSS pins (CL) and a capacitor for stabilizing
the input between VIN and VSS pins (CIN), the distance from the capacitors to these pins should be as
short as possible.
Note that the output voltage may increase when a series regulator is used at low load current (1.0 mA or
less).
Generally a series regulator may cause oscillation, depending on the selection of external parts. The
following conditions are recommended for this IC. However, be sure to perform sufficient evaluation
under the actual usage conditions for selection, including evaluation of temperature characteristics.
Input capacitor (CIN):
1.0
F or more
Output capacitor (CL):
0.47
F or more
Equivalent series resistance (ESR): 10
or less
The voltage regulator may oscillate when the impedance of the power supply is high and the input
capacitor is small or an input capacitor is not connected.
The application conditions for the input voltage, output voltage, and load current should not exceed the
package power dissipation.
Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in
electrostatic protection circuit.
In determining the output current, attention should be paid to the output current value specified in Table
4 in the electrical characteristics and footnote *5) of the table.
SII claims no responsibility for any disputes arising out of or in connection with any infringement by
products including this IC of patents owned by a third party.
相關PDF資料 |
PDF描述 |
|---|---|
| S02-BDS-3-B(LF)(SN) | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER |
| S02-BDS-3-B | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SOLDER |
| SM02-BDS-3-TB(LF)(SN) | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| SM02-BDS-3-TB | 2 CONTACT(S), MALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| S100-12 | 100 WATTS - 12.5 VOLTS 1.5-30 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-T111B23MC-OGITFG | 功能描述:低壓差穩壓器 - LDO Linear LDO Reg Hi 50uA Iq 150mA Iout RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| S-T111B24MC-OGJTFG | 功能描述:低壓差穩壓器 - LDO Linear LDO Reg Hi 50uA Iq 150mA Iout RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| S-T111B25MC-OGKTFG | 功能描述:低壓差穩壓器 - LDO Linear LDO Reg Hi 50uA Iq 150mA Iout RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| S-T111B25MC-OGKTFU | 功能描述:IC REG LINEAR 150MA SOT23-5 制造商:ablic u.s.a. inc. 系列:* 包裝:剪切帶（CT） 零件狀態:在售 電流 - 輸出:150mA 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商器件封裝:SOT-23-5 標準包裝:1 |
| S-T111B26MC-OGLTFG | 功能描述:低壓差穩壓器 - LDO Linear LDO Reg Hi 50uA Iq 150mA Iout RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。