- 您現在的位置：買賣IC網 > PDF目錄297336 > S-93C66AFJ-TBP 256 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | S-93C66AFJ-TBP |
| 元件分類： | PROM |
| 英文描述： | 256 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 封裝： | SOP-8 |
| 文件頁數： | 27/30頁 |
| 文件大?。?/td> | 419K |
| 代理商： | S-93C66AFJ-TBP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁
CMOS SERIAL E2PROM
S-93C46A/56A/66A
Rev. 2.3_00
Seiko Instruments Inc.
6
Operation
Instructions (in the order of start-bit, instruction, address, and data) are latched to DI in synchronization with the rising
edge of SK after CS goes high. A start-bit can only be recognized when the high of DI is latched to the rising edge of SK
when CS goes from low to high, it is impossible for it to be recognized as long as DI is low, even if there are SK pulses after
CS goes high. Any SK pulses input while DI is low are called "dummy clocks." Dummy clocks can be used to adjust the
number of clock cycles needed by the serial IC to match those sent out by the CPU. Instruction input finishes when CS goes
low, where it must be low between commands during tCDS.
All input, including DI and SK signals, is ignored while CS is low, which is stand-by mode.
1. Read
The READ instruction reads data from a specified address. After A0 is latched at the rising edge of SK, DO output
changes from a high-impedance state (Hi-Z) to low level output. Data is continuously output in synchronization with the rise
of SK.
When all of the data (D0) in the specified address has been read, the data in the next address can be read with the input
of another SK clock. Thus, it is possible for all of the data addresses to be read through the continuous input of SK clocks as
long as CS is high.
The last address (An
A1 A0 = 1
11) rolls over to the top address (An
A1 A0 = 0
00).
Figure 5 Read Timing (S-93C56A)
Figure 4 Read Timing (S-93C46A)
A5A4A3A2A1A0+1
A5A4A3A2A1A0+2
D15
D15 D14
D14 D13
D14
Hi-Z
D13
D0
D1
D2
D15
0
Hi-Z
A0
A1
A2
A3
A4
A5
0
1
28
27
26
25
24
23
12
11
10
9
8
7
6
5
4
3
2
1
44
43
42
41
40
39
D13
D0
D1
D2
CS
SK
DI
DO
A0
A6
12
45
29
14
D15
D15 D14
D14 D13
D14
Hi-Z
A6A5A4A3A2A1A0+1
D13
D0
D1
D2
D15
0
Hi-Z
A1
A2
A3
A4
A5
X
0
1
28
27
26
25
24
11
10
9
8
7
6
5
4
3
2
1
44
43
42
41
40
A6A5A4A3A2A1A0+2
D13
D0
D1
D
2
13
CS
SK
DI
DO
相關PDF資料 |
PDF描述 |
|---|---|
| S-AV10L | 135 MHz - 155 MHz RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| S-AV16H | 150 MHz - 160 MHz RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| S-AV16L | 135 MHz - 150 MHz RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| S-AV16VH | 160 MHz - 174 MHz RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| S-T111B39MC-OGYTFU | 3.9 V FIXED POSITIVE LDO REGULATOR, 0.26 V DROPOUT, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-93C66AFT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS SERIAL E2PROM |
| S-93C66AFT-TB | 功能描述:電可擦除可編程只讀存儲器 4K (256X16) 3-Wire RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| S-93C66AMFN | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:CMOS SERIAL E2PROM |
| S-93C66AMFN-TB | 功能描述:電可擦除可編程只讀存儲器 4K (256X16) Hi-Speed RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| S-93C66B | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:CMOS SERIAL E2PROM |
發布緊急采購，3分鐘左右您將得到回復。