參數資料
型號: S-80148CNPF-JK9TFGG
元件分類: 電源管理
英文描述: 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4
封裝: LEAD FREE, SNT-4
文件頁數: 11/33頁
文件大?。?/td> 297K
代理商: S-80148CNPF-JK9TFGG
ULTRA-SMALL PACKAGE HIGH-PRECISION VOLTAGE DETECTOR WITH DELAY CIRCUIT (INTERNAL DELAY TIME SETTING)
Rev.4.0_00
S-801 Series
Seiko Instruments Inc.
19
5. Oscillation
In applications where a resistor is connected to the voltage detector input (Figure 17), taking a
CMOS active low products for example, the through-type current which is generated when the
output goes from low to high (release) causes a voltage drop equal to [through-type current]
× [input
resistance] across the resistor. When the input voltage drops below the detection voltage (–VDET) as
a result, the output voltage goes to low level. In this state, the through-type current stops and its
resultant voltage drop disappears, and the output goes from low to high. The through-type current is
again generated, a voltage drop appears, and repeating the process finally induces oscillation.
OUT
VSS
VDD
RB
RA
VIN
S-801
Figure 17 Example for Bad Implementation of Input Voltage Divider
Precautions
In the S-801 series products, the through-type current flows at a frequency of 20 kHz approximately
during the delay time since the internal oscillator circuit and counter timer operate at voltage release.
High impedance in the input may cause oscillation by the through-type current. When the input
impedance is high, insert a capacitor between VDD pin and VSS pin to prevent oscillation.
Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in
electrostatic protection circuit.
In CMOS output products of the S-801 Series, the through-type current flows at detection and release. If
the impedance is high, oscillation may occur due to the voltage drop by the through-type current during
releasing.
When designing for mass production using an application circuit described herein, the product deviation
and temperature characteristics should be taken into consideration. SII shall not bear any responsibility
for the patents on the circuits described herein.
SII claims no responsibility for any and all disputes arising out of or in connection with any infringement of
the products including this IC upon patents owned a third party.
相關PDF資料
PDF描述
S7AH-03E1000 1-OUTPUT 3 W DC-DC REG PWR SUPPLY MODULE
SN74LVC1G3157DRYR 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PDSO6
S-1009N32I-N4T1U 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4
S-80140ALMC-JAZT2U 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5
S-8357G33MC-MIST2U SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO5
相關代理商/技術參數
參數描述
S-80149ALMC-JBAT2G 功能描述:電壓監測器/監控器 Volt Detect Built-in Delay 1.3uA Iq RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT
S-80149ALPF-JBATFG 功能描述:電壓監測器/監控器 Volt Detect Built-in Delay 1.3uA Iq RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT
S-80149ANMC-JDAT2G 功能描述:電壓監測器/監控器 Volt Detect Built-in Delay 1.3uA Iq RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT
S-80149ANPF-JDATFG 功能描述:電壓監測器/監控器 Volt Detect Built-in Delay 1.3uA Iq RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT
S-80149BLMC-JFAT2G 功能描述:電壓監測器/監控器 Volt Detect Built-in Delay 1.3uA Iq RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT