- 您現在的位置：買賣IC網 > PDF目錄374612 > S-4543A (Seiko Instruments Inc.) Dot Matrix LCD Driver(點陣LCD驅動器) PDF資料下載
參數資料
| 型號： | S-4543A |
| 廠商： | Seiko Instruments Inc. |
| 英文描述： | Dot Matrix LCD Driver(點陣LCD驅動器) |
| 中文描述： | 點陣LCD驅動器（點陣液晶驅動器） |
| 文件頁數： | 13/27頁 |
| 文件大?。?/td> | 163K |
| 代理商： | S-4543A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Dot Matrix LCD Driver
S-4543A
12
Seiko Instruments Inc.
2.2 Serial Interface
P / SX
E1, E2
R / WX
A0
D0
D1
D2
D3
～
D7
: Serial interface (Connected to VSS).
: “L” active.
: “L” write instruction.
: “L” command data.
: Serial data input pin (SDI)
: Serial clock input pin (SCLK)
: Serial data output pin (SDO)
: Open
“H” is reset.
“H” read instruction.
“H” displayed data.
Note: The displayed data write instruction and read instruction cannot activate E1 and E2 at the same time.
By setting P/SX to “L”, the serial interface is selected.
The instruction code is the same as for the parallel interface.
By setting E1, and E2 to “H”, the serial interface circuit is reset and the counter is initialized. Either E1 or E2 is
set to “L”, the serial interface enters an operating state.
The commands and displayed data are written at the rising edge of serial clock. Data is input in the order D0 to
D7 in 8-bit data. The status and displayed data are read at the falling edge of the serial clock.
Further, displayed data reading needs dummy reading.
E1 and E2 cannot be set to “L” at the same time when displayed data is written or read out.
Status reading in a reset operation is invalidated at the time the serial interface is selected. However, “H” is
output to the D2 pin (SD0: serial data output pin).
Serial clock wiring must be made by considering external noise and reflecting noise. Be sure to check the
operation of the equipment.
A0
RWX
D0 (SDI)
D2 (SDO)
0
0
1
1
0
1
0
1
Command write
Invalid
Data write
Invalid
Status read
Status read
Status read
Data read (Note)
A0
R / WX
Operation
L
H
L
H
L
H
H
L
Command input
Displayed data reading
Status reading
Displayed data writing
Figure 6 Read/Write Timings of Serial Interface Display Data
D0
D1
D2
D3
D4
D5
D6
D7
A0
R/WX
D1
(SCLK)
D0
(SDI)
E1, E2
D0
D1
D2
D3
D4
D5
D6
D7
D2
(SDO)
Note: Data reading needs dummy reading.
D0
D0
相關PDF資料 |
PDF描述 |
|---|---|
| S-4544A | LCD Controller-Driver With Built-in 8-Bit and Serial Interfaces(內置8位和串行接口的LCD控制器-驅動器) |
| S-4561A | LCD Controller-Driver With Built-in Serial and Parallel interfaces(內置串行和并行接口的LCD控制器-驅動器) |
| S-4562A | LCD CONTROLLER DRIVER |
| S-4601A | 64-bit THERMAL HEAD DRIVER |
| S-4602A | CMOS Thermal Print Head Driver Containing a 64-Bit Shift Register and a Latch(內置一個64位移位寄存器和一個鎖存器的CMOS 熱敏打印頭驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-4544A | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:LCD Controller-Driver |
| S4545 | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:T1/CEPT/ISDN-PRI TRANSFORMER |
| S455-003 | 制造商:Tripp Lite 功能描述:SCSI ULTRA2/U160/U320 LVD/SE CABLE - CHDC168(M) / HD68(M) - - Bulk |
| S455-006 | 功能描述:CABLE SCSI VHDCI68M/HD68M 6' RoHS:是 類別:電纜組件 >> 系列間適配器電纜 系列:- 標準包裝:1 系列:- 其它名稱:VS-M12MSD-RJ45-933-B/ 5,0VS-M12MSD-RJ45-933-B/5,0 |
| S455-010 | 功能描述:CABLE SCSI VHDCI68M/HD68M 10' RoHS:是 類別:電纜組件 >> 系列間適配器電纜 系列:- 標準包裝:1 系列:- 其它名稱:VS-M12MSD-RJ45-933-B/ 5,0VS-M12MSD-RJ45-933-B/5,0 |
發布緊急采購，3分鐘左右您將得到回復。