- 您現在的位置：買賣IC網 > PDF目錄374610 > S-29590A (Seiko Instruments Inc.) 16Kbit Serial EEPROM(16K位串行EEPROM) PDF資料下載
參數資料
| 型號： | S-29590A |
| 廠商： | Seiko Instruments Inc. |
| 英文描述： | 16Kbit Serial EEPROM(16K位串行EEPROM) |
| 中文描述： | 16Kbit串行EEPROM（16K的位串行EEPROM的） |
| 文件頁數： | 8/43頁 |
| 文件大小： | 167K |
| 代理商： | S-29590A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
CMOS SERIAL E
2
PROM
S-29590A / 29690A
7
2. Write (PROGRAM)
The PROGRAM instruction automatically begins writing to the non-volatile memory when CS goes low at the
completion of the specified clock input.
The write operation is completed in 10 ms (t
PR
Max.), and the typical write period is less than 4 ms. In the S-29590A /
690A series, it is easy to VERIFY the completion of the write operation in order to minimize the write cycle by setting CS to
high and checking the DO pin, which is low during the write operation and high after its completion. This VERIFY
procedure can be executed over and over again. There are two methods to detect a change in the DO output. One is to
detect a change from low to high setting CS to high, and the other is to detect a change from low to high as a result of
repetitious operations of returning the CS to low after setting CS to high and checking the DO output.
Because all SK and DI inputs are ignored during the write operation, any input of instruction will also be disregarded.
When DO outputs high after completion of the write operation or if it is in the high-impedence state (Hi-Z), the input of
instructions is available. Even if the DO pin remains high, it will enter the high-impedence state upon the recognition of a
high of DI (start-bit) attached to the rising edge of an SK pulse. (see Figure 3).
DI input should be low during the VERIFY procedure.
2.1 PROGRAM
This instruction writes 16-bit data to a specified address.
After changing CS to high, input a start-bit, op-code (PROGRAM), address, and 16-bit data. If there is a data overflow
of more than 16 bits, only the last 16-bits of the data is considered valid. Changing CS to low will start the PROGRAM
operation. It is not necessary to make the data "1" before initiating the PROGRAM operation.
A9
A10
32
X
t
CDS
11
t
PR
busy
ready
D15
Hi-Z
t
SV
16
Hi-Z
17
10
9
8
7
6
5
3
2
1
SK
DI
DO
A0
D0
4
t
HZ1
0
A5
A6
A7
A8
0
1
ready
CS
VERIFY
*On the S-29590A, A
10
is optional.
Figure 5
Write Timing (S-29690A)
相關PDF資料 |
PDF描述 |
|---|---|
| S-29690A | 32Kbit Serial EEPROM(32K位串行EEPROM) |
| S-29L130A | 1Kbit CMOS Serial EEPROM(1K位CMOS串行EEPROM) |
| S-29L131A | 1Kbit CMOS Serial EEPROM(1K位CMOS串行EEPROM) |
| S-29L220A | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| S-29L220ADFE | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S295-93-328-30-571100 | 制造商:Mill-Max Mfg Corp 功能描述: |
| S295-M04-F12-C | 制造商:UNICORP 功能描述: |
| S295-M04-F12-F | 制造商:UNICORP 功能描述: |
| S2974320530100200 | 制造商:MILL-MAX 功能描述: |
| S297-M04-F13-E | 制造商:UNICORP 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。