- 您現在的位置：買賣IC網 > PDF目錄378206 > RTL8201 (Electronic Theatre Controls, Inc.) REALTEK SINGLE CHIP SINGLE PORT 10/100M FAST ETHERNET PHYCEIVER RTL8201BL PDF資料下載
參數資料
| 型號： | RTL8201 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | REALTEK SINGLE CHIP SINGLE PORT 10/100M FAST ETHERNET PHYCEIVER RTL8201BL |
| 中文描述： | 瑞昱單片單端口10/100M自適應快速以太網PHYCEIVER RTL8201BL |
| 文件頁數： | 7/29頁 |
| 文件大?。?/td> | 335K |
| 代理商： | RTL8201 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
RTL8201BL
2002-03-29
Rev.1.2
7
5.6 LED Interface/PHY Address Config
These five pins are latched into the RTL8201BL during power up reset to configure PHY address [0:4] used for MII
management register interface. And then, in normal operation after initial reset, they are used as driving pins for status
indication LED. The driving polarity, active low or active high, is determined by each latched status of the PHY address [4:0]
during power-up reset. If latched status is High then it will be active low, and if latched status is Low then it will be active high.
Refer to Section 7.5 for more information.
Symbol
PHYAD0/
LED0
PAD1/
LED1
PHYAD2/
LED2
Type
LI/O
Pin No.
9
Description
PHY Address [0]
Link LED:
Active when linked.
PHY Address [1]
Full Duplex LED:
Active when in Full Duplex operation.
PHY Address [2]
Link 10/ACT LED:
Active when linked in 10Base-T mode, and blinking
when transmitting or receiving data.
PHY Address [3]
Link 100/ACT LED:
Active when linked in 100Base-TX and blinking
when transmitting or receiving data.
PHY Address [4]
Collision LED:
Active when collisions occur.
LI/O
10
LI/O
12
PHYAD3/
LED3
LI/O
13
PHYAD4/
LED4
LI/O
15
5.7 Reset and other pins
Symbol
RESETB
Type
I
Pin No.
42
Description
RESETB:
Set low to reset the chip. For a complete reset function, this pin
must be asserted low for at least 10ms.
Power Feedback Output:
Be sure to connect a 22uF tantalum capacitor for
frequency compensation and a 0.1uF capacitor for noise de-coupling. Then
connect this pin through a ferrite bead to PWFBIN(pin8). The connection
method is figured in section 7.11.
Power Feedback Input:
see the description of PWFBOUT.
Not connection
PWFBOUT
O
32
PWFBIN
NC
I
8
27
5.8 Power and Ground pins
Symbol
AVDD33
Type
P
Pin No.
36
Description
3.3V Analog power input:
3.3V power supply for analog circuit; should be
well decoupled.
Analog Ground:
Should be connected to a larger GND plane
3.3V Digital Power input:
3.3V power supply for digital circuit.
Digital Ground:
Should be connected to a larger GND plane.
AGND
DVDD33
DGND
P
P
P
29,35
14,48
11,17,45
相關PDF資料 |
PDF描述 |
|---|---|
| RTL8201BL | REALTEK SINGLE CHIP SINGLE PORT 10/100M FAST ETHERNET PHYCEIVER RTL8201BL |
| RTL8208 | REALTEK SINGLE CHIP OCTAL 10/100 MBPS FAST ETHERNET TRANSCEIVER |
| RTOB | precision resistors |
| RTO-B | precision resistors |
| RTS8505C | The RTS8505C is a caller ID integrated chip with call waiting function. An 8-bit microprocessor (6502) has been built in the chip and it provides a co |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RTL8201BL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REALTEK SINGLE CHIP SINGLE PORT 10/100M FAST ETHERNET PHYCEIVER RTL8201BL |
| RTL8201BL-LF | 制造商:Realtek Semiconductor 功能描述: |
| RTL8201CP | 制造商:Realtek 功能描述:10M/100M |
| RTL8201CP-LF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP/SINGLE-PORT 10/100M FAST ETHERNET PHYCEIVER (With Auto Crossover) |
| RTL8201CP-VD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP/SINGLE-PORT 10/100M FAST ETHERNET PHYCEIVER (With Auto Crossover) |
發布緊急采購，3分鐘左右您將得到回復。