- 您現在的位置：買賣IC網 > PDF目錄225135 > RT9229CS (Electronic Theatre Controls, Inc.) Advaced Dual PWM and Dual Linear Power Controller PDF資料下載
參數資料
| 型號： | RT9229CS |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 線性穩壓 |
| 英文描述： | Advaced Dual PWM and Dual Linear Power Controller |
| 中文描述： | 進展期雙PWM和線性雙電源控制器 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 219K |
| 代理商： | RT9229CS |
RT9229
DS9229-03 July 2001
www.richtek-ic.com.tw
5
Functional Pin Description
UGATE1, UGATE2 (Pins 27 and 1)
Connect UGATE pins to the respective PWM
converter’s upper MOSFET gate. This pin provides
the gate drive for the upper MOSFETs.
PHASE1, PHASE2 (Pins 26 and 2)
Connect the PHASE pins to the PWM converter’s
upper MOSFET source. These pins are used to
monitor the voltage drop across the upper MOSFETs
for over-current protection.
VID0, VID1, VID2, VID3, VID4 (Pin 7, 6, 5, 4, and 3)
VID0~4 are the input pins to the 5-bit DAC. The
states of these five pins program the internal voltage
reference, DACOUT. The level of DACOUT sets the
core converter output voltage (VOUT1). It also sets
the core PGOOD and OVP thresholds. Table 1
specifies the DACOUT voltage of 32 combinations of
VID levels.
PGOOD (Pin 8)
PGOOD is an open collector output used to indicate
the status of the PWM converter output voltage. This
pin is pulled low when the core output is not within
±10% of the DACOUT reference voltage, or when
any of the other outputs are below their under-
voltage thresholds. The PGOOD output is open for
‘11111’VID code. See table 1.
FB1, FB2 (21 and 10)
FB1, 2 are the available external pins of the PWM
error amplifiers. Both the FB pins are the inverting
input of the error amplifiers.
OCSET1, OCSET2 (Pins 23 and 9)
Connect a resistor (ROCSET) from this pin to the drain
of the upper MOSFET. ROCSET, an internal 200
A
current source (IOCSET), and the upper MOSFET on-
resistance (RDS(ON)) set the converter over-current
(OC) trip point according to the following equation:
IOCSET×ROCSET
IPEAK =
RDS(ON)
An over-current trip cycles the soft-start function.
Sustaining an over-current for 2 soft-start intervals
shuts down the controller.
SS (Pin 12)
Connect a capacitor from this pin to ground. This
capacitor, along with an internal 11
A (VSS>1V)
current source, sets the soft-start interval of the
converter.
Pulling this pin low with an open drain signal will shut
down the IC.
FAULT (Pin 13)
This pin is low during normal operation, but it is
pulled to about 8V (VCC = 12V) in the event of an
over-voltage or over-current condition.
FB4 (Pin 14)
Connect this pin to a resistor divider to set the linear
regulator output.
VSEN1, VSEN2 (Pins 22 and 15)
These pins are connected to the PWM converters’
output voltage. The PGOOD and OVP comparator
circuits use these signals to report output voltage
status and for over-voltage protection. VSEN2
provides the input power to the integrated linear
regulator.
相關PDF資料 |
PDF描述 |
|---|---|
| RTE0200N04 | ROTARY SWITCH-2POSITIONS, SPDT, LATCHED, 0.1A, 30VDC, THROUGH HOLE-STRAIGHT |
| RTE0310N04 | ROTARY SWITCH-3POSITIONS, SP3T, LATCHED, 0.1A, 30VDC, THROUGH HOLE-STRAIGHT |
| RTE1000V14 | ROTARY CODED SWITCH-10POSITIONS, BINARY CODED DECIMAL, LATCHED, 0.1A, 30VDC, THROUGH HOLE-RIGHT ANGLE |
| RTE1000V13 | ROTARY CODED SWITCH-10POSITIONS, BINARY CODED DECIMAL, LATCHED, 0.1A, 30VDC, THROUGH HOLE-RIGHT ANGLE |
| RTE1000V15 | ROTARY CODED SWITCH-10POSITIONS, BINARY CODED DECIMAL, LATCHED, 0.1A, 50VDC, THROUGH HOLE-RIGHT ANGLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RT9230 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.5V ADVANCED DUAL PWM AND DUAL LINEAR POWER CONTROLLER |
| RT9230CS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.5V ADVANCED DUAL PWM AND DUAL LINEAR POWER CONTROLLER |
| RT9231 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Advaned PWM and Triple Linear Power Controller |
| RT9231A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| RT9231-CS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Advaned PWM and Triple Linear Power Controller |
發布緊急采購，3分鐘左右您將得到回復。