- 您現在的位置：買賣IC網 > PDF目錄378201 > RT9172F-25CG (Electronic Theatre Controls, Inc.) Hex Inverter; Package: SOIC 14 LEAD; No of Pins: 14; Container: Tape and Reel; Qty per Container: 2500 PDF資料下載
參數資料
| 型號： | RT9172F-25CG |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Hex Inverter; Package: SOIC 14 LEAD; No of Pins: 14; Container: Tape and Reel; Qty per Container: 2500 |
| 中文描述： | 3A固定輸出電壓LDO穩壓器 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 342K |
| 代理商： | RT9172F-25CG |
RT9172
Preliminary
www.richtek-ic.com.tw
8
DS9172-03 April 2002
Functional Description
Capacitor Selection
The RT9172 requires a minimum input capacitance of
1
μ
F between the input and ground pins to prevent any
impedance interactions with the supply. The RT9172
requires a minimum of 10
μ
F (tantalum, or electrolytic)
capacitance between the output and ground pins for
proper operation, if used 10
μ
F ceromic please parrell
with 100
μ
F tantalum or electrolytic. Larger capacitance
provides better load dynamics and noise performance.
Error Operation (FLG)
The RT9172 produces a logic low signal at the FLG pin
when the output drops out of regulation due to low input
voltage, current limiting, or thermal limiting.
The internal error FLG comparator has an open drain
output stage. Hence, the FLG pin should be pulled high
through a pull up resistor.
Sense Pin
In applications where the regulator output is not very
close to the load, RT9172 can provide better remote
load regulation using the SENSE pin. Fig.2 and Fig.3
depict the advantage of the SENSE option. RT9172
regulates the voltage at the output pin. Hence, the
voltage at the remote load will be the regulator output
voltage minus the drop across the trace resistance. For
example, in the case of a 3.3V output, if the trace
resistance is 100m
, the voltage at the remote load will
be 3V with 3A of load current, I
LOAD
. The RT9172
regulates the voltage at the sense pin. Connecting the
sense pin to the remote load will provide regulation at
the remote load, as shown in Fig.2 and Fig.3.
Chip Enable Operation
A CMOS logic level signal at the chip enable (EN) pin
will turn-off the regulator. Pin EN must be actively
terminated through a 10k
pull-up resistor for a proper
operation. If this pin is driven from a source that actively
pulls high and low (such as a CMOS rail to rail
comparator), the pull-up resistor is not required. This
pin must be tied to V
IN
if not used.
Dropout Voltage
The dropout voltage of a regulator is defined as the
minimum input-to-output differential required to stay
within 2% of the output voltage. The RT9172 uses an
internal MOS-FET with an R
DS(ON)
160m
. For
CMOS LDOs, the dropout voltage is the product of the
load current and the R
DS(ON)
of the internal MOSFET.
Maximum Output Current Capability
RT9172 can deliver a continuous current of 1.5 A over
the full operating temperature range. A heatsink may
be required depending on the maximum power
dissipation and maximum ambient temperature of the
application. Under all possible conditions, the junction
temperature must be within the range specified under
operating conditions. The total power dissipation of
the device is given by:
PD = (V
IN
- V
OUT
) I
OUT
+ (V
IN
) I
GND
where I
GND
is the operating ground current of the
device (specified under Electrical Characteristics).
The maximum allowable temperature rise (T
RMAX
)
depends on the maximum ambient temperature
(T
AMAX
) of the application, and the maximum
allowable junction temperature (T
JMAX
):
T
RMAX
= T
JMAX
– T
AMAX
The maximum allowable value for junction to ambient
Thermal Resistance,
θ
JA
=
T
RMAX
-
T
AMAX
The maximum allowable value for junction to ambient
Thermal Resistance,
θ
JA
, can be calculated using the
formula:
θ
JA
=
T
RMAX
/
P
D
RT9172 are available in TO-220, TO-263, and SOT-
223 packages. The thermal resistance depends in
amount of copper area or heat sink, and on air flow. If
the maximum allowable value of
θ
JA
calculated above
is
≧
60
°
C/W for TO-220 package,
≧
60
°
C/W for
TO-263 package, and
≧
140
°
C/W for SOT-223
package, no heatsink is needed since the package
can
dissipate
enough
requirements. If the value for allowable
θ
JA
falls below
these limits, a heat sink is required.
heat
to
satisfy
these
相關PDF資料 |
PDF描述 |
|---|---|
| RT9172F-25CM | Hex Inverter; Package: TSSOP-14; No of Pins: 14; Container: Tape and Reel; Qty per Container: 2500 |
| RT9172F-25CT | Hex Inverter; Package: TSSOP-14; No of Pins: 14; Container: Tape and Reel; Qty per Container: 2500 |
| RT9172F-25CT5 | Hex Inverter; Package: SOEIAJ-14; No of Pins: 14; Container: Tape and Reel; Qty per Container: 2000 |
| RT9172F-26CG | Hex Inverter; Package: SOEIAJ-14; No of Pins: 14; Container: Tape and Reel; Qty per Container: 2000 |
| RT9172F-26CM | Quad XOR Gate; Package: PDIP-14; No of Pins: 14; Container: Rail; Qty per Container: 500 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RT9173AGL5 | 功能描述:IC REG BUS TERMINATIN 3A TO252-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| RT9173AGM5 | 功能描述:IC REG BUS TERMINATIN 3A TO263-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| RT9173APL5 | 制造商:Richtek Technology Corporation 功能描述: |
| RT9173APM5 | 制造商:Richtek Technology Corporation 功能描述: |
| RT9173BGL5 | 功能描述:IC REG BUS TERMINATIN 2A TO252-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。