- 您現在的位置：買賣IC網 > PDF目錄385772 > RT8010BGQW (Richtek Technology Corporation) 1.5MHz, 800mA, High Efficiency PWM Step-Down DC/DC Converter PDF資料下載
參數資料
| 型號： | RT8010BGQW |
| 廠商： | Richtek Technology Corporation |
| 英文描述： | 1.5MHz, 800mA, High Efficiency PWM Step-Down DC/DC Converter |
| 中文描述： | 1.5MHz的，800mA電流，高效率的PWM降壓型DC / DC轉換器 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 265K |
| 代理商： | RT8010BGQW |
RT8010B
9
DS8010B-00 July 2007
www.richtek.com
Preliminary
The output ripple is the highest at maximum input voltage
since
Δ
I
L
increases with input voltage. Multiple capacitors
placed in parallel may be needed to meet the ESR and
RMS current handling requirements. Dry tantalum, special
polymer, aluminum electrolytic and ceramic capacitors are
all available in surface mount packages. Special polymer
capacitors offer very low ESR but have lower capacitance
density than other types. Tantalum capacitors have the
highest capacitance density but it is important to only
use types that have been surge tested for use in switching
power supplies. Aluminum electrolytic capacitors have
significantly higher ESR but can be used in cost-sensitive
applications provided that consideration is given to ripple
current ratings and long term reliability. Ceramic capacitors
have excellent low ESR characteristics but can have a
high voltage coefficient and audible piezoelectric effects.
The high Q of ceramic capacitors with trace inductance
can also lead to significant ringing.
Using Ceramic Input and Output Capacitors
Higher values, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Their high ripple
current, high voltage rating and low ESR make them ideal
for switching regulator applications. However, care must
be taken when these capacitors are used at the input and
output. When a ceramic capacitor is used at the input
and the power is supplied by a wall adapter through long
wires, a load step at the output can induce ringing at the
input, V
IN
. At best, this ringing can couple to the output
and be mistaken as loop instability. At worst, a sudden
inrush of current through the long wires can potentially
cause a voltage spike at V
IN
large enough to damage the
part.
Output Voltage Programming
The resistive divider allows the FB pin to sense a fraction
of the output voltage as shown in Figure 4.
)
R2
R1
(1
V
V
REF
OUT
+
=
Figure 4. Setting the Output Voltage
where V
REF
is the internal reference voltage (0.6V typ.)
For adjustable voltage mode, the output voltage is set by
an external resistive divider according to the following
equation :
Efficiency Considerations
The efficiency of a switching regulator is equal to the output
power divided by the input power times 100%. It is often
useful to analyze individual losses to determine what is
limiting the efficiency and which change would produce
the most improvement. Efficiency can be expressed as :
Efficiency = 100%
(L1+ L2+ L3+ ...)
where L1, L2, etc. are the individual losses as a percentage
of input power. Although all dissipative elements in the
circuit produce losses, two main sources usually account
for most of the losses : VIN quiescent current and I
2
R
losses.
The VIN quiescent current loss dominates the efficiency
loss at very low load currents whereas the I
2
R loss
dominates the efficiency loss at medium to high load
currents. In a typical efficiency plot, the efficiency curve
at very low load currents can be misleading since the
actual power lost is of no consequence.
1. The VIN quiescent current appears due to two factors
including : the DC bias current as given in the electrical
characteristics and the internal main switch and
synchronous switch gate charge currents. The gate charge
current results from switching the gate capacitance of the
internal power MOSFET switches. Each time the gate is
switched from high to low to high again, a packet of charge
Δ
Q moves from V
IN
to ground.
The resulting
Δ
Q/
Δ
t is the current out of V
IN
that is typically
larger than the DC bias current. In continuous mode,
I
GATECHG
= f(Q
T
+Q
B
)
where Q
T
and Q
B
are the gate charges of the internal top
and bottom switches. Both the DC bias and gate charge
losses are proportional to V
IN
and thus their effects will
be more pronounced at higher supply voltages.
2. I
2
R losses are calculated from the resistances of the
internal switches, R
SW
and external inductor R
L
.
RT8010B
GND
FB
R1
R2
V
OUT
相關PDF資料 |
PDF描述 |
|---|---|
| RT8011 | 2A, 4MHz, Synchronous Step-Down Regulator |
| RT8011AGF | 2A, 4MHz, Synchronous Step-Down Regulator |
| RT8011AGQW | 2A, 4MHz, Synchronous Step-Down Regulator |
| RT8011APF | 2A, 4MHz, Synchronous Step-Down Regulator |
| RT8011APQW | 2A, 4MHz, Synchronous Step-Down Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RT8010GQW | 功能描述:IC REG BUCK SYNC ADJ 1A 6WDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:50 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:5 V ~ 25 V 輸入電壓:2.3 V ~ 5.5 V PWM 型:電流模式 頻率 - 開關:600kHz，1.2MHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 包裝:管件 供應商設備封裝:8-MSOP |
| RT8011 | 制造商:RICHTEK 制造商全稱:Richtek Technology Corporation 功能描述:2A, 4MHz, Synchronous Step-Down Regulator |
| RT8011AGF | 制造商:RICHTEK 制造商全稱:Richtek Technology Corporation 功能描述:2A, 4MHz, Synchronous Step-Down Regulator |
| RT8011AGQW | 功能描述:IC REG BUCK SYNC ADJ 2A 8WDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:升壓（升壓） 輸出類型:兩者兼有 輸出數:1 輸出電壓:5V，2 V ~ 16.5 V 輸入電壓:2 V ~ 16.5 V PWM 型:- 頻率 - 開關:45kHz 電流 - 輸出:50mA 同步整流器:無 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:8-PDIP |
| RT8011APF | 制造商:RICHTEK 制造商全稱:Richtek Technology Corporation 功能描述:2A, 4MHz, Synchronous Step-Down Regulator |
發布緊急采購，3分鐘左右您將得到回復。