- 您現在的位置：買賣IC網 > PDF目錄373327 > RT2S-MC-OD16-12 PDF資料下載
參數資料
| 型號： | RT2S-MC-OD16-12 |
| 文件頁數： | 8/8頁 |
| 文件大小： | 443K |
| 代理商： | RT2S-MC-OD16-12 |
RT-2
22
2. Operating environment
1) Use the product at ambient operating
temperature between 0
and 131
°
F
. (When installing in the control
panel, take heat release into due consid-
eration. Installing of the product at 90 de-
grees to the control panel is
recommended. When installing the prod-
uct horizontally or placing it on a heating
unit, use a cooking fan.)
2) Keep the supply voltage within the
range of 90% V to 110% V of the rated
voltage.
3) Keep the product as far as possible
from power cables, high tension equip-
ment, power equipment, equipment with
transmitting devices such as amateur ra-
dios, or equipment which generates a
large switching surge.
4) The main unit is made of resin; there-
fore, do not use it in areas where it may
come in contact with (or be exposed to)
organic solvents such as benzine, thinner,
and alcohol or strong alkaline substances
such as ammonia and caustic soda.
5) Do not use the product in areas where
it may be exposed to flammable gases,
corrosive gases, excessive dust, or mois-
ture, or areas where it may be subjected
to strong vibration or shock.
3. Dropping
If a unit is dropped be sure to check its ex-
ternal appearance and characteristics be-
fore using it.
4. Installing and removing the module
1) Firmly insert the module into the socket
with the terminals going in the direction of
the blade receptacles.
2) The module can be easily removed us-
ing the removal key.
(1) Insert the removal key into the socket
slots.
°
C and 55
°
C
32
°
F
(2) Pull the removal key up to remove the
module.
5. Wiring and circuit configuration
1) Make all connections according to the
schematic. Polarity should be observed
when wiring DC type.
2) Use of wire-pressed terminal is recom-
mended for connections to pressure con-
nector connect type. For the wire-direct
connect type, strip wire ends to the spec-
ified length.
3) When wiring power lines or power ca-
bles, twisted pair treatment (standed wire
treatment) should be done in order to im-
prove noise resistance.
4) When the load output device is an in-
ductive load type, installing a diode and
surge absorber to both ends of the load is
recommended.
5) In order to improve noise resistance,
class 3 grounding of the control panel is
recommended.
6) Do not pass the wiring over the surface
of the case. (When unavoidable, keep the
wire at least 3 cm
1.181 inch
away from
the surface of the case.)
7) Turn off the power before connecting/
disconnecting connector cables.
8) With some types of control devices,
leakage current may cause the relay to fail
to turn off after the control input is turned
off. Make sure that the relay turns off after
the control input is turned off.
6. Installation
1) Perform mounting hole cutout accord-
ing to the panel cutout drawings.
2) When installing the unit on a DIN rail,
use the DIN rail locking lever on the side
of the unit. Installation is accomplished by
simply fitting the unit onto the rail and
pressing gently.
3) To remove the unit from the DIN rail,
use a flat head screwdriver to pull out the
DIN rail locking lever.
7. Transporting and storage
1) If the product is subjected to extreme
vibration while being transported, the re-
lays may become detached, the lead may
become bent, and the unit may become
damaged. Handle the inner and outer
boxes with care.
2) If the product is stored in an extremely
adverse environment, visible defects and
deterioration of performance characteris-
tics may result. We recommend the fol-
lowing storage conditions.
Temperature: 5 to 30
°
C
41 to 86
°
F
Humidity: Max. 60% R.H.
Environment: No hazardous sub-
stances such as sulfurous acid gases
and little dust.
DIN rail locking lever
DIN rail
1
2
3
First push in
the DIN rail
locking lever.
Hook the holders on the
unit over the DIN rail.
Press the unit onto
the DIN rail.
3
Remove the unit from
the DIN rail.
1
Insert the tip of the
flat head screwdriver
into the slot in the
DIN rail locking lever.
2
Move the
screwdriver in
the direction
of the arrows,
and pull out
the lever.
相關PDF資料 |
PDF描述 |
|---|---|
| RT2S-MC-OD16-24 | |
| RT2S-M-ID16-12 | |
| RT2S-M-ID16-24 | |
| RT2S-M-OD16-12 | |
| RT2S-M-OD16-24 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RT2S-MC-OD16-24 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| RT2S-M-ID16-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| RT2S-M-ID16-24 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| RT2S-M-OD16-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| RT2S-M-OD16-24 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。