- 您現在的位置：買賣IC網 > PDF目錄373323 > RS485-C1(AS) RS232/RS485 CONV (AS) PDF資料下載
參數資料
| 型號： | RS485-C1(AS) |
| 英文描述： | RS232/RS485 CONV (AS) |
| 中文描述： | RS232/RS485接口換（AS）的 |
| 文件頁數： | 16/18頁 |
| 文件大?。?/td> | 986K |
| 代理商： | RS485-C1(AS) |
RS232-RS485 Convertor Manual V1.02 28/06/01
7
3.2 PRO101 Hardware Installation Instructions
Place the PRO101 programmers side-by-side on a flat surface allowing sufficient space
in front of each programmer to place the ‘ISP Interface Modules’ and ‘Target Systems’.
Remove the lid of each programmer by removing the four screws in the lid.
Set the ‘Communications Mode Switch’ (S2) to ‘RS-485’.
Set the Communications Node Address to the required unique address (0 to 15).
Plug the 9-way RS-232 cable into the port on the RS-232 to RS-485 convertor and
connect further PRO101 programmers as shown in the diagram below.
Figure 10
Plug an RS-485 network cable from one of the RS-485 outputs on the RS-485 convertor
to the ‘RS-485 Input’ connector on the rear panel of the first PRO101.
Plug another RS-485 network cable from the ‘RS-485 Output’ connector on the rear
panel of the first PRO101 to the next PRO101 in the chain.
A return RS-485 cable from the last PRO101 in the chain to the RS-485 convertor is
NOT required.
Power up the PC.
Plug in the power supply adaptor supplied with the RS-232/RS-485 convertor into a
spare mains socket.
Power up all PRO101 programmers.
Launch the ISP-PRO software on the PC and set up the required number of PPM’s
within the software.
Test that all PPM’s are communicating with the PC at their correct ‘Node Address’. (The
Node Address may be changed while the programmer is powered up).
When all PRO101’s are recognised by the ISP-PRO software, power down all
programmers and replace lids.
相關PDF資料 |
PDF描述 |
|---|---|
| RS485-C1(EU) | RS232/RS485 CONV (EU) |
| RS485-C1(UK) | RS232/RS485 CONV (UK) |
| RS485-C1(US) | RS232/RS485 CONV (US) |
| RS485 | RS-422 AND RS-485 APPLICATION NOTE |
| RS56-PCI | Host Software Processed V.90/K56flex Modem Device Family for Desktop Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RS485-C2(UN) | 制造商:Equinox Technologies 功能描述:MODULE CONVERTER RS232 TO RS485 |
| RS485-CAB | 制造商:Carlo Gavazzi 功能描述: |
| RS-485EVALBOARD1 | 功能描述:其他開發工具 TVS/TBU/GDT Eval Board RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓: |
| RS-485EVALBOARD2 | 功能描述:其他開發工具 TVS/TBU/MOV Eval Board RoHS:否 制造商:Parallax 產品:ELEV-8 Hex Upgrade Kits 類型:Robotics 工具用于評估:ELEV-8 Quadcopter 工作電源電壓: |
| RS485-FL-DPLX-EVM | 功能描述:SN65HVD3x, SN65HVD5x, SN65HVD7x, SN65HVD147x, SN65HVD179x - Interface, Transceiver, RS-485 Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:接口，收發器，RS-485 嵌入式:- 使用的 IC/零件:SN65HVD3x，SN65HVD5x，SN65HVD7x，SN65HVD147x，SN65HVD179x 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。