- 您現在的位置：買賣IC網 > PDF目錄374599 > RMPA2265 (FAIRCHILD SEMICONDUCTOR CORP) Dual Band WCDMA Power Amplifier Module 1850 to 1910 MHz and 1920 to 1980 MHz PDF資料下載
參數資料
| 型號： | RMPA2265 |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 衰減器 |
| 英文描述： | Dual Band WCDMA Power Amplifier Module 1850 to 1910 MHz and 1920 to 1980 MHz |
| 中文描述： | 1850 MHz - 1910 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| 封裝： | 3 X 3 MM, 1 MM HEIGHT, LEAD FREE, LCC-8 |
| 文件頁數： | 9/11頁 |
| 文件大小： | 484K |
| 代理商： | RMPA2265 |
2004 Fairchild Semiconductor Corporation
RMPA2265 Rev.
E
R
Applications Information
CAUTION: THIS IS AN ESD SENSITIVE DEVICE.
Precautions to Avoid Permanent Device Damage:
Cleanliness: Observe proper handling procedures to
ensure clean devices and PCBs. Devices should remain
in their original packaging until component placement to
ensure no contamination or damage to RF, DC and
ground contact areas.
Device Cleaning: Standard board cleaning techniques
should not present device problems provided that the
boards are properly dried to remove solvents or water
residues.
Static Sensitivity: Follow ESD precautions to protect
against ESD damage:
– A properly grounded static-dissipative surface on
which to place devices.
– Static-dissipative floor or mat.
– A properly grounded conductive wrist strap for each
person to wear while handling devices.
General Handling: Handle the package on the top with a
vacuum collet or along the edges with a sharp pair of
bent tweezers. Avoiding damaging the RF, DC, and
ground contacts on the package bottom. Do not apply
excessive pressure to the top of the lid.
Device Storage: Devices are supplied in heat-sealed,
moisture-barrier bags. In this condition, devices are
protected and require no special storage conditions.
Once the sealed bag has been opened, devices should
be stored in a dry nitrogen environment.
Device Usage:
Fairchild recommends the following procedures prior to
assembly.
Dry-bake devices at 125°C for 24 hours minimum. Note:
The shipping trays cannot withstand 125°C baking
temperature.
Assemble the dry-baked devices within 7 days of
removal from the oven.
During the 7-day period, the devices must be stored in an
environment of less than 60% relative humidity and a
maximum temperature of 30°C
If the 7-day period or the environmental conditions have
been exceeded, then the dry-bake procedure must be
repeated.
Solder Materials & Temperature Profile:
Reflow soldering is the preferred method of SMT
attachment. Hand soldering is not recommended.
Reflow Profile
Ramp-up: During this stage the solvents are evaporated
from the solder paste. Care should be taken to prevent
rapid oxidation (or paste slump) and solder bursts
caused by violent solvent out-gassing. A typical heating
rate is 1-2°C/sec.
Pre-heat/soak: The soak temperature stage serves two
purposes; the flux is activated and the board and devices
achieve a uniform temperature. The recommended soak
condition is: 120–150 seconds at 150°C.
Reflow Zone: If the temperature is too high, then devices
may be damaged by mechanical stress due to thermal
mismatch or there may be problems due to excessive
solder oxidation. Excessive time at temperature can
enhance the formation of inter-metallic compounds at
the lead/board interface and may lead to early
mechanical failure of the joint. Reflow must occur prior to
the flux being completely driven off. The duration of peak
reflow temperature should not exceed 10 seconds.
Maximum soldering temperatures should be in the range
215–220°C, with a maximum limit of 225°C.
Cooling Zone: Steep thermal gradients may give rise to
excessive thermal shock. However, rapid cooling
promotes a finer grain structure and a more crack-
resistant solder joint. The illustration below indicates the
recommended soldering profile.
Solder Joint Characteristics:
Proper operation of this device depends on a reliable void-
free attachment of the heat sink to the PWB. The solder
joint should be 95% void-free and be a consistent
thickness.
Rework Considerations:
Rework of a device attached to a board is limited to reflow
of the solder with a heat gun. The device should not be
subjected to more than 225°C and reflow solder in the
molten state for more than 5 seconds. No more than 2
rework operations should be performed.
相關PDF資料 |
PDF描述 |
|---|---|
| RMPA2271 | WCDMA/UMTS Power Edge Power Amplifier Module with Integrated Power Detector |
| RMPA2450 | 2.4-2.5 GHz GaAs MMIC Power Amplifier |
| RMPA2451 | 2.4?2.5 GHz GaAs MMIC Power Amplifier |
| RMPA2451-TB | 2.4?2.5 GHz GaAs MMIC Power Amplifier |
| RMPA2453 | 2.4?2.5 GHz InGaP HBT Linear Power Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RMPA2266 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Fairchild Semiconductor Corporation 功能描述: |
| RMPA2271 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:WCDMA/UMTS Power Edge Power Amplifier Module with Integrated Power Detector |
| RMPA2450 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:2.4-2.5 GHz GaAs MMIC Power Amplifier |
| RMPA2451 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| RMPA2451-TB | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:2.4?2.5 GHz GaAs MMIC Power Amplifier |
發布緊急采購，3分鐘左右您將得到回復。