- 您現在的位置：買賣IC網 > PDF目錄378161 > RM-V211T (Sony Corporation) Operating Instructions Mode d’emploi PDF資料下載
參數資料
| 型號： | RM-V211T |
| 廠商： | Sony Corporation |
| 英文描述： | Operating Instructions Mode d’emploi |
| 中文描述： | 操作說明模式科特迪瓦就業部 |
| 文件頁數： | 1/2頁 |
| 文件大?。?/td> | 112K |
| 代理商： | RM-V211T |
To use this Remote Commander with a Sony brand component that
is already preset at the factory (see the table on the left), you can skip
this procedure.
If you are using other brand’s component or if you cannot operate
even a Sony brand component, follow this procedure.
Setting by Entering the Code Number
See the supplied “Component Code Numbers” and find the code for
your component.
1
Press the S (Set) button.
2
Press the button of the component that you want to set up.
3
Enter the three-digit component code in the “Component
Code Numbers” table.
For example, to set a Philips’ TV, press
-86
.
4
Press the
t
button.
5
Aim this Commander to your component and check if you can
operate it using this Commander.
Go through the same procedure for each component you want to set
up.
If you cannot operate your component...
First, try repeating these set up procedures using the other codes
listed for your component (see “Component Code Numbers”).
If — after trying all the codes listed for your component — you still
cannot get the Commander to work properly, try the search
method described under “Setting by Searching for the Correct
Code”.
Notes
Be sure to proceed to each next step in the above procedure within 10
seconds; otherwise, the setting mode will be canceled.
You cannot set up more than one component at a time on each component
select buttons. If you want to set up two or more same components of
different brands, see “Setting Another TV, VCR, DVD, or Satellite Tuner”.
Tip
You can write down the code number on the label inside the battery
compartment lid.
About this Remote Commander
You can set up this Remote Commander to operate the following
components of almost all major brands including Sony.
Installing the Batteries
Open the battery compartment and insert two R6 (size AA) batteries
(not supplied).
Be sure to line up the + and – on the batteries with the + and – on the
battery compartment.
1
2
When to replace the batteries
Under normal conditions, batteries will last up to six months. If the
Remote Commander does not operate properly, the batteries might
be worn out. Replace the batteries with new ones.
Notes
Replace both batteries with new ones.
Do not take more than 20 minutes to replace the batteries; otherwise, your
setting of the code numbers will be erased.
Notes on Batteries
Do not mix old batteries with new ones or mix different types of
batteries together.
If the electrolyte inside the battery should leak, wipe the
contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the electrolyte
from leaking, remove the batteries when you plan not to use the
Commander for a long period of time.
Setting by Searching for the Correct Code
If you’ve tried all the code numbers listed for your component and
you still cannot get the Commander to work (or if your component
was not listed), try the following.
1
Turn on the component you wish to set up using its power
switch.
2
Press the
S
(Set)
3
Press the button of the component that you want to set up.
4
Aim the Commander to your component, and press and release
the
PROGR+
button. Then press and release the
5
Repeat step 4 until the correct code number is found.
Each time you press the
new code number will be transmitted.
Keep trying until your component operates as follows:
TV, VCR, DVD, or satellite tuner : the power turns off.
TV without a power switch: the Channel + function works.
Be patient as you do this; it may take up to about 120 tries for a
TV, and about 60 tries for VCR, and about 70 tries for satellite
tuner, and about 20 tries for DVD, until the correct code number
is located.
6
When the correct code is found, press the
7
Turn on the component again, and check that the Commander
can control the other functions of your component such as
channel and volume control.
button, a
If the component does not operate properly, repeat steps 2 to 6 and
search for another code.
If you still cannot get the Commander to work properly, see
“Troubleshooting”.
Note
Be sure to proceed to each next step in the above procedure within 10 seconds;
otherwise setting mode will be canceled.
Setting Another TV, VCR, DVD,or Satellite Tuner
When you have two or more components of the same type (for
example, three VCRs), you can change the component’s type on
button and
SAT
button.
1
Press the
S
(Set) button.
2
Press the
DVD
or
3
Press the
x
button.
4
Press one of the following buttons;
-
to set up a DVD
1
to set up a VCR
3
to set up a satellite tuner
8
to set up a TV
5
Press the
t
button.
6
Enter the component’s code number by following steps 1 to 5 of
“Setting by Entering the Code Number”, or steps 2 to 7 of
“Setting by Searching for the Correct Code”.
Operating a Component
1
Press the button of the desired component on the
Commander.
2
Point the Commander directly to your component and press
the button for the desired function.
See “Remote Button Descriptions” for details.
Notes on using the Commander
Using this Commander will not add new functions to your components. The
functions of the Commander are limited to the functions of the component
itself. For example, if your TV does not have a mute function, the
on this Commander will not function with your TV.
Do not forcibly remove or tear off the corner protector.
button
RM-V211T
Setting the Component Codes
Remote Commander
Operating Instructions
Mode d’emploi
(au verso)
Sony Corporation 2001
Printed in Malaysia
English
Position
TV
VCR
DVD
SAT
Component that can be preset
TV
VCR
Factory setting
Sony TV
Sony VHS VCR (VTR3)
Sony DVD
Sony satellite tuner
TV, VCR, DVD, or satellite tuner
3-230-684-
11
(1)
相關PDF資料 |
PDF描述 |
|---|---|
| RM3182 | ARINC 429 Differential Line Driver |
| RM3182L | ARINC 429 Differential Line Driver |
| RM3182S | ARINC 429 Differential Line Driver |
| RM5231-150-Q | RM5231⑩ Microprocessor with 32-Bit System Bus Data Sheet Released |
| RM5231 | RM5231⑩ Microprocessor with 32-Bit System Bus Data Sheet Released |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RM-V400U | 制造商:JVC Worldwide 功能描述:REMOCON UNIT |
| RM-V41U | 制造商:JVC Worldwide 功能描述:REMOCON UNIT |
| RMVA | 制造商:HELLERMANNTYTON 功能描述:CATV VIDEO AMPLIFIER MODULE 制造商:HellermannTyton 功能描述:CATV video amplifier module |
| RMVLZ620 | 制造商:Sony 功能描述:Sony 8 Device Universal Remote 制造商:SONY 功能描述:SONY UNIVERSAL REMOTE 8 DEVICE UNIVERSAL |
| RMVP13450DF | 制造商:Samsung Semiconductor 功能描述:RF-M for supporting NTSC-M , vertical with F-connector, 4 ground tab. |
發布緊急采購，3分鐘左右您將得到回復。
