- 您現在的位置：買賣IC網 > PDF目錄385769 > RF2513 (RF MICRO DEVICES INC) UHF TRANSMITTER PDF資料下載
參數資料
| 型號： | RF2513 |
| 廠商： | RF MICRO DEVICES INC |
| 元件分類： | 通信及網絡 |
| 英文描述： | UHF TRANSMITTER |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO24 |
| 封裝： | PLASTIC, SSOP-24 |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 321K |
| 代理商： | RF2513 |
11-28
RF2513
Rev B8 010509
11
T
the charge pump to create a control voltage for the
voltage controlled oscillator.
The
voltage controlled oscillator (VCO)
is a tuned
differential amplifier with the bases and collectors
cross-coupled to provide positive feedback and a 360°
phase shift. The tuned circuit is located in the collec-
tors. It is comprised of internal varactors and two exter-
nal inductors. The designer selects the inductors for
the desired frequency of operation. These inductors
also provide DC bias for the VCO. The output of the
VCO is buffered and applied to the prescaler circuit,
where it is divided down and compared to the refer-
ence oscillator frequency.
The PLL and VCO circuitry can be enabled by setting
applying a “high” logic level to pin 4 (PLL ENABL).
Conversely, the PLL and VCO circuitry will be turned
off if the level is tied “l(fā)ow”.
The
transmit amplifier
is a two stage amplifier con-
sisting of a driver and an open collector final stage. It is
capable of providing 8dBm of output power into a 50
load while operating from a 3.6V power supply.
The output power is adjustable by the setting of pin 7
(LVL ADJ). This analog input allows the designer a
15dB range of output power. As the LVL ADJ voltage is
reduced, the output power and current consumption
are reduced. LVL ADJ must be low when the transmit-
ter is disabled.
Additionally, the transmitter circuitry can be disabled
entirely by applying a “l(fā)ow” logic level to pin 11 (TX
ENABL). During transmission, this pin should be tied
“high”. This pin controls all circuitry except for the PLL
circuitry.
During transmission the transmitter is enabled and the
impedance of the output pin, pin 8 (TX OUT), is low.
When the transmitter is not enabled, the impedance
becomes high.
The RF2513 contains onboard band gap reference
voltage circuitry which provides a stable
DC bias
over
varying temperature and supply voltages.
Designing with the RF2513
The
reference oscillator
is built around the onboard
transistor at pins 1, 2 and 3. The intended topology is
of a Colpitts oscillator. The Colpitts oscillator is quite
common and requires few external components, mak-
ing it ideal for low cost solutions. The topology of this
type of oscillator is as seen in the following figure.
This type of oscillator is a parallel resonant circuit for a
fundamental mode crystal. The transistor amplifier is
an emitter follower and the voltage gain is developed
by the tapped capacitor impedance transformer. The
series combination of C
1
and C
2
act in parallel with the
input capacitance of the transistor to capacitively load
the crystal.
The nominal capacitor values can be calculated with
the following equations.
and
The load capacitance is usually 32pF. The variable
freq
is the oscillator frequency in MHz. The frequency can
be adjusted by either changing C
2
or by placing a vari-
able capacitor in series with the crystal. As an exam-
ple, assume a desired frequency of 14MHz and a load
capacitance of 32pF. C
1
=137.1pF and C
2
=41.7pF.
These capacitor values provide a starting point. The
drive level of the oscillator should be checked by look-
ing at the signal at pin 2 (OSC E). It has been found
that the level at this pin should generally be around
500mV
PP
or less. This will reduce the reference spur
levels and reduce noise from distortion. If this level is
higher than 500mV
PP
then decrease the value of C
1
.
The values of these capacitors are usually tweaked
during design to meet performance goals, such as
minimizing the start-up time.
Additionally, by placing a variable capacitor in series
with the crystal, one is able to adjust the frequency.
This will also alter the drive level, so it should be
checked again.
An important part of the overall design is the voltage
controlled oscillator (VCO). The VCO is configured as
a differential amplifier. The VCO is tuned via the exter-
nal inductors, capacitor and varactor. The varactor
capacitance is set by the loop filter output voltage
through a 4k
resistor.
V
CC
C2
C1
X1
C
1
60
C
freq
MHz
-----------------------
=
C
2
C
load
-------------
C
1
------
–
--------------------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| RF2514 | VHF/UHF TRANSMITTER |
| RF2516 | VHF/UHF TRANSMITTER |
| RF2601 | GAIN CONTROLLED IF AMPLIFIER |
| RF2603 | 2.8V PCS UPCONVERTER |
| RF2607 | CDMA/FM RECEIVE AGC AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2514 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER |
| RF2514_06 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER |
| RF2514_1 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER |
| RF2514PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER |
| RF2514PCBA-41X | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER |
發布緊急采購，3分鐘左右您將得到回復。