- 您現在的位置：買賣IC網 > PDF目錄230917 > RDC-19229S-122Q (DATA DEVICE CORP) SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CQCC44 PDF資料下載
參數資料
| 型號： | RDC-19229S-122Q |
| 廠商： | DATA DEVICE CORP |
| 元件分類： | 位置變換器 |
| 英文描述： | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CQCC44 |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 276K |
| 代理商： | RDC-19229S-122Q |
14
Data Device Corporation
www.ddc-web.com
RDC-19220/2S
E-11/02-300
INHIBIT, ENABLE, AND CB TIMING
The Inhibit (INH) signal is used to freeze the digital output angle
in the transparent output data latch while data is being trans-
ferred. Application of an inhibit signal does not interfere with the
continuous tracking of the converter. As shown in FIGURE 13,
angular output data is valid 150 ns maximum after the applica-
tion of the negative inhibit pulse.
Output angle data is enabled onto the tri-state data bus in two
bytes. Enable MSBs (EM) is used for the most significant 8 bits
and Enable LSBs (EL) is used for the least significant 8 bits. As
shown in FIGURE 14, output data is valid 150 ns maximum after
the application of a negative enable pulse. The tri-state data bus
returns to the high impedance state 100 ns maximum after the
rising edge of the enable signal.
The Converter Busy (CB) signal indicates that the tracking con-
verter output angle is changing 1 LSB. As shown in FIGURE 15,
output data is valid 50 ns maximum after the middle of the CB
pulse. The CB pulse width is 1/40 Fs, which is nominally 375 ns.
BUILT-IN-TEST (BIT)
The Built-ln-Test output (BIT) monitors the level of error from the
demodulator. This signal is the difference in the input and output
angles and ideally should be zero; if it exceeds approximately
100 LSBs (of the selected resolution) the logic level at BIT will
change from a logic 1 to a logic 0.
This condition will occur during a large step and reset after the
converter settles out. BIT will also change to logic 0 for an over-
velocity condition, because the converter loop cannot maintain
input-output or if the converter malfunctions where it cannot
maintain the loop at a null. BIT will also be set low for a detected
Loss-of-Signal (LOS) and/or a Loss-of-Reference (LOR). The
BIT signal may pulse during certain error conditions, i.e., when
the converter is in a spin around condition or the signal amplitude
is on the threshold of LOS.
LOS will be detected if both sin and cos input voltages are less
than 500 mV peak. LOR will be detected if the differential refer-
ence voltage is less than 500 mV peak.
;;
;;;
DATA
VALID
150 ns max
INHIBIT
;
100 ns MAX
ENABLE
150 ns MAX
DATA
VALID
HIGH Z
;
1/40 FS
(375 nsec nominal)
CB
50 ns
DATA
VALID
DATA
VALID
FIGURE 13. INHIBIT TIMING
FIGURE 14. ENABLE TIMING
FIGURE 15. CONVERTER BUSY TIMING
相關PDF資料 |
PDF描述 |
|---|---|
| RDC-19229S-172S | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CQCC44 |
| RD-14592D1-385Q | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, MDMA36 |
| RD-14596D1-322Y | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, DIP36 |
| RD-14596F1-194L | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36 |
| RD-14597D1-455K | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, DIP36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RDC20-100M-RC | 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Radial Drum Core Inductors |
| RDC20-101K-RC | 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Radial Drum Core Inductors |
| RDC20-102K-RC | 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Radial Drum Core Inductors |
| RDC20110D05 | 功能描述:DC/DC CONVERTER +/-5V 20W 制造商:xp power 系列:RDC 包裝:管件 零件狀態:有效 類型:隔離模塊 輸出數:2 電壓 - 輸入（最小值）:55V 電壓 - 輸入（最大值）:176V 電壓 - 輸出 1:5V 電壓 - 輸出 2:-5V 電壓 - 輸出 3:- 電流 - 輸出（最大值）:2A，2A 功率（W） - 制造系列:20W 電壓 - 隔離:1.5kV（1500V） 應用:軌道 特性:遠程開/關，OCP，OTP，OVP，SCP，UVLO 安裝類型:通孔 封裝/外殼:6-DIP 模塊 大小/尺寸:2.00" 長 x 1.00" 寬 x 0.42" 高（50.8mm x 25.4mm x 10.6mm） 工作溫度:-40°C ~ 85°C 效率:86% 功率（W） - 最大值:20W 標準包裝:10 |
| RDC20110D12 | 功能描述:DC/DC CONVERTER +/-12V 20W 制造商:xp power 系列:RDC 包裝:管件 零件狀態:有效 類型:隔離模塊 輸出數:2 電壓 - 輸入（最小值）:55V 電壓 - 輸入（最大值）:176V 電壓 - 輸出 1:12V 電壓 - 輸出 2:-12V 電壓 - 輸出 3:- 電流 - 輸出（最大值）:830mA，830mA 功率（W） - 制造系列:20W 電壓 - 隔離:1.5kV（1500V） 應用:軌道 特性:遠程開/關，OCP，OTP，OVP，SCP，UVLO 安裝類型:通孔 封裝/外殼:6-DIP 模塊 大小/尺寸:2.00" 長 x 1.00" 寬 x 0.42" 高（50.8mm x 25.4mm x 10.6mm） 工作溫度:-40°C ~ 85°C 效率:84% 功率（W） - 最大值:20W 標準包裝:10 |
發布緊急采購，3分鐘左右您將得到回復。