- 您現在的位置：買賣IC網 > PDF目錄69313 > R5F3651NNFC MICROCONTROLLER, PQFP128 PDF資料下載
參數資料
| 型號： | R5F3651NNFC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, PQFP128 |
| 封裝： | 20 X 14 MM, 0.50 MM PITCH, LQFP-128 |
| 文件頁數： | 14/81頁 |
| 文件大小： | 879K |
| 代理商： | R5F3651NNFC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
112
4317K–AVR–03/2013
AT90PWM2/3/2B/3B
For more information on how to access the 16-bit registers refer to “Accessing 16-bit Registers”
15.5.1
Input Capture Trigger Source
The trigger sources for the Input Capture unit arethe Input Capture pin (ICP1A & ICP1B).
Be aware that changing trigger source can trigger a capture. The Input Capture Flag must there-
fore be cleared after the change.
The Input Capture pin (ICPn) IS sampled using the same technique as for the Tn pin (Figure 13-
1 on page 84). The edge detector is also identical. However, when the noise canceler is
enabled, additional logic is inserted before the edge detector, which increases the delay by four
system clock cycles. Note that the input of the noise canceler and edge detector is always
enabled unless the Timer/Counter is set in a Waveform Generation mode that uses ICRn to
define TOP.
An Input Capture can be triggered by software by controlling the port of the ICPn pin.
15.5.2
Noise Canceler
The noise canceler improves noise immunity by using a simple digital filtering scheme. The
noise canceler input is monitored over four samples, and all four must be equal for changing the
output that in turn is used by the edge detector.
The noise canceler is enabled by setting the Input Capture Noise Canceler (ICNCn) bit in
Timer/Counter Control Register B (TCCRnB). When enabled the noise canceler introduces addi-
tional four system clock cycles of delay from a change applied to the input, to the update of the
ICRn Register. The noise canceler uses the system clock and is therefore not affected by the
prescaler.
15.5.3
Using the Input Capture Unit
The main challenge when using the Input Capture unit is to assign enough processor capacity
for handling the incoming events. The time between two events is critical. If the processor has
not read the captured value in the ICRn Register before the next event occurs, the ICRn will be
overwritten with a new value. In this case the result of the capture will be incorrect.
When using the Input Capture interrupt, the ICRn Register should be read as early in the inter-
rupt handler routine as possible. Even though the Input Capture interrupt has relatively high
priority, the maximum interrupt response time is dependent on the maximum number of clock
cycles it takes to handle any of the other interrupt requests.
Using the Input Capture unit in any mode of operation when the TOP value (resolution) is
actively changed during operation, is not recommended.
Measurement of an external signal’s duty cycle requires that the trigger edge is changed after
each capture. Changing the edge sensing must be done as early as possible after the ICRn
Register has been read. After a change of the edge, the Input Capture Flag (ICFn) must be
cleared by software (writing a logical one to the I/O bit location). For measuring frequency only,
the clearing of the ICFn Flag is not required (if an interrupt handler is used).
15.6
Output Compare Units
The 16-bit comparator continuously compares TCNTn with the Output Compare Register
(OCRnx). If TCNT equals OCRnx the comparator signals a match. A match will set the Output
Compare Flag (OCFnx) at the next “timer clock cycle”. If enabled (OCIEnx = 1), the Output Com-
pare Flag generates an Output Compare interrupt. The OCFnx Flag is automatically cleared
when the interrupt is executed. Alternatively the OCFnx Flag can be cleared by software by writ-
相關PDF資料 |
PDF描述 |
|---|---|
| R5F3650ENFA | MICROCONTROLLER, PQFP100 |
| R5F3650TDFB | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100 |
| R5F36506NFB | MICROCONTROLLER, PQFP100 |
| R5F3650TDFA | MICROCONTROLLER, PQFP100 |
| R5F3650KNFB | MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R5F3651RDFC | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F3651RDFC#U0 | 功能描述:MCU 4KB FLASH 640/16K 128-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/60/65 標準包裝:96 系列:PIC® 16F 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:I²C，SPI 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:11 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):2.3 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 包裝:管件 |
| R5F3651RNFC | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:This MCU consumes low power, and supports operating modes |
| R5F3651TDFC | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F3651TDFC#U0 | 功能描述:MCU 4KB FLASH 768/16K 128-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/60/65 標準包裝:96 系列:PIC® 16F 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:I²C，SPI 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:11 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):2.3 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。