參數資料
型號: R5F3651KDFC
元件分類: 微控制器/微處理器
英文描述: MICROCONTROLLER, PQFP128
封裝: 20 X 14 MM, 0.50 MM PITCH, LQFP-128
文件頁數: 48/81頁
文件大?。?/td> 879K
代理商: R5F3651KDFC
66
4317K–AVR–03/2013
AT90PWM2/3/2B/3B
values are read back again, but as previously discussed, a nop instruction is included to be able
to read back the value recently assigned to some of the pins.
Note:
1. For the assembly program, two temporary registers are used to minimize the time from pull-
ups are set on pins 0, 1, 6, and 7, until the direction bits are correctly set, defining bit 2 and 3
as low and redefining bits 0 and 1 as strong high drivers.
11.2.5
Digital Input Enable and Sleep Modes
As shown in Figure 11-2, the digital input signal can be clamped to ground at the input of the
schmitt-trigger. The signal denoted SLEEP in the figure, is set by the MCU Sleep Controller in
Power-down mode, Power-save mode, and Standby mode to avoid high power consumption if
some input signals are left floating, or have an analog signal level close to V
CC/2.
SLEEP is overridden for port pins enabled as external interrupt pins. If the external interrupt
request is not enabled, SLEEP is active also for these pins. SLEEP is also overridden by various
other alternate functions as described in “Alternate Port Functions” on page 67.
If a logic high level (“one”) is present on an Asynchronous External Interrupt pin configured as
“Interrupt on Rising Edge, Falling Edge, or Any Logic Change on Pin” while the external interrupt
is not enabled, the corresponding External Interrupt Flag will be set when resuming from the
above mentioned sleep modes, as the clamping in these sleep modes produces the requested
logic change.
TABLE 2.
Assembly Code Example(1)
...
; Define pull-ups and set outputs high
; Define directions for port pins
ldi
r16, (1<<PB7)|(1<<PB6)|(1<<PB1)|(1<<PB0)
ldi
r17, (1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0)
out
PORTB, r16
out
DDRB, r17
; Insert nop for synchronization
nop
; Read port pins
in
r16, PINB
...
C Code Example
unsigned char
i;
...
/* Define pull-ups and set outputs high */
/* Define directions for port pins */
PORTB = (1<<PB7)|(1<<PB6)|(1<<PB1)|(1<<PB0);
DDRB = (1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0);
/* Insert nop for synchronization*/
_NOP();
/* Read port pins */
i = PINB;
...
相關PDF資料
PDF描述
R5F21217KFP 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP48
R5F21275SNFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32
R5F2L388ADFA 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80
R5F21154DSP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO20
RVPXA272FC5416 32-BIT, 416 MHz, RISC PROCESSOR, PBGA336
相關代理商/技術參數
參數描述
R5F3651KDFC#U0 功能描述:MCU 4KB FLASH 384/16K 128-LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:M16C™ M16C/60/65 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI,I²C,IEBus,IrDA,SIO,UART/USART 外圍設備:DMA,POR,PWM,WDT 輸入/輸出數:121 程序存儲器容量:384KB(384K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b,D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
R5F3651KNFC 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:This MCU consumes low power, and supports operating modes
R5F3651MCDFC 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:televisions, household appliances, office equipment, communication devices
R5F3651MCDFC#V0 制造商:Renesas Electronics Corporation 功能描述:M16C/65C 528+8/31 128LQFP 14X20 -40 TO +85 - Trays 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 512KB FLASH 128LQFP
R5F3651MCNFC 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:televisions, household appliances, office equipment, communication devices