參數資料
型號： R295CH38CD8
廠商： WESTCODE SEMICONDUCTORS LTD
元件分類： 晶閘管
英文描述： 1755 A, 3800 V, SCR
封裝： 101A223, 3 PIN
文件頁數： 13/15頁
文件大?。?/td> 297K
代理商： R295CH38CD8
WESTCODE
Positive development in power electronics
R295CH36 to R295CH40
Provisional Data Sheet. Types R295CH36 to R295CH40 Issue 1
Page 5 of 13
August, 2000
The total dissipation is now given by:
f
E
W
(original)
(TOT)
+
=
12.2 Determination without Measurement
In circumstances where it is not possible to measure voltage and current conditions, or for design
purposes, the additional losses E in joules may be estimated as follows.
Let E be the value of energy per reverse cycle in joules (curves in Figure 9).
Let f be the operating frequency in Hz
()
(
)
()
f
R
E
T
th
original
SINK
new
SINK
=
Where TSINK (new) is the required maximum heat sink temperature and
TSINK (original) is the heat sink temperature given with the frequency ratings.
A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage
to a peak value (Vrm) of 67% of the maximum grade. If a different grade is being used or Vrm is other than
67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value
obtained from the curves.
NOTE 1- Reverse Recovery Loss by Measurement
This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring
the charge care must be taken to ensure that:
(a) a.c. coupled devices such as current transformers are not affected by prior passage of high
amplitude forward current.
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically
damped snubber, connected across diode anode to cathode. The formula used for the calculation
of this snubber is shown below:
dt
di
S
r
C
V
R
= 4
2
Where: Vr
= Commutating source voltage
CS = Snubber capacitance
R
= Snubber resistance
13.0 Gate Drive
The recommended pulse gate drive is 20V, 10
with a short-circuit current rise time of not more than
0.5s. This gate drive must be applied when using the full di/dt capability of the device.
The duration of pulse may need to be configured with respect to the application but should be no shorter
than 20s, otherwise an increase in pulse current could be needed to supply the resulting increase in
charge to trigger.
相關PDF資料
PDF描述
R295CH38CD9 1755 A, 3800 V, SCR
R295CH36D2G1 1755 A, 3600 V, SCR
R295CH36D2G2 1755 A, 3600 V, SCR
R295CH36D2G3 1755 A, 3600 V, SCR
R295CH36D2G4 1755 A, 3600 V, SCR
相關代理商/技術參數
參數描述
R29621 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
R29621ADM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
R29621ADM/883B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
R29621ADMS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
R29621DM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*