- 您現在的位置：買賣IC網 > PDF目錄299836 > R1215D002F-TR-F (RICOH COMPANY LTD) 0.08 A SWITCHING CONTROLLER, 1400 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | R1215D002F-TR-F |
| 廠商： | RICOH COMPANY LTD |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.08 A SWITCHING CONTROLLER, 1400 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | ROHS COMPLIANT, SON-8 |
| 文件頁數： | 20/20頁 |
| 文件大?。?/td> | 363K |
| 代理商： | R1215D002F-TR-F |
R1215D
9
Output Voltage Setting Method and Phase Compensation Making Method
The feedback voltage is controlled into 1.0V. The output voltage can be set with divider resistors for voltage
setting, R1 and R2 as shown in typical application of the previous page. Refer to the next formula.
Output Voltage
= VFB× (R1+R2)/R2
Output Voltage is adjustable with setting various resistor values combination.
R1
+R2 should be equal or less than 500kΩ
As for the DC/DC converter, depending on the load current and external components such as L and C, phase
may loss around 180°. In such case, phase margin becomes less and may be unstable. To avoid this situation,
make the phase margin more. The pole is made with external components L and C.
Fpole
1/{2×π×
(
)
3
C
L
×
}
C4, C5, R3, and R4 shown in the diagram are for making phase compensation. The gain of the system can be
set with using these resistors and capacitors. Each value in the diagram is just an example.
R4 and C5 make zero (the backward phase).
Fzero
1/(2×π×R4×C5)
Choose the R4 and C5 value so as to make the cutoff frequency of this zero point close to the cutoff frequency of
the pole by external components, L and C.
For example, supposed that L
=10μH and COUT (C3) =15μF, the cutoff frequency of the pole is approximately
13kHz. Therefore make the cutoff frequency of the zero point close to 13kHz. Then R4
=4.7kΩ and C5=2200pF
are appropriate values.
As for setting the gain, the ratio of the composite resistor (RT: RT
=R1×R2/(R1+R2)) to R4 is the key.
If the R4 against the composite resistor, RT, is large, the gain becomes also large. If the gain is large, the
response characteristic is improved, however, too large gain makes the system be unstable.
If the spike noise of VOUT may be large, the spike noise may be picked into VFB pin, and the unstable operation
may result. In this case, a resistor R3, shown in typical application of the previous page. The recommended
resistance value of R3 is in the range from 1k
Ω to 5kΩ. Then, noise level will be decreased.
Further, R1 and C4 makes another zero point (the backward phase).
Fzero
1/(2×π×R1×C4)
Make the cutoff frequency of this zero point be lower than the cutoff frequency of the pole by external
components, or, L and C. Herein, R1
=160kΩ and C4=1000pF are appropriate values.
Select the Power MOSFET, the diode, capacitors and the inductor within ratings (Voltage, Current, Power) of
this IC. Choose the power MOSFET with low threshold voltage depending on the input voltage to be able to
turn on the FET completely. Choose the diode with low VF such as Shottky type with low reverse current IR,
and with fast switching speed. When an external transistor is switching, spike voltage may be generated
caused by an inductor, therefore recommended voltage tolerance of capacitor connected to VOUT is twice as
much as the setting voltage or more.
The soft-start time and the maximum duty cycle setting method
The soft-start time and the maximum duty cycle can be set with R5, R6, and C7 values connected to the
VREFOUT pin and the DTC pin. (Refer to the timing chart: Soft-start operation.)
相關PDF資料 |
PDF描述 |
|---|---|
| R1215D002A-TR-F | 0.08 A SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO8 |
| R1218K042A-TR | 1 A SWITCHING REGULATOR, 1400 kHz SWITCHING FREQ-MAX, DSO6 |
| R1223N3.62E-TL | Analog IC |
| R1223N3.62E-TR | Analog IC |
| R1223N3.62F-TL | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R12163 | 功能描述:烙鐵 IDEAL THERMOTIP 500W RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| R121630003 | 功能描述:RF 連接器 SSMA HERMETIC SLDR MNT RCPT RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
| R121653000 | 功能描述:RF 連接器 EMB A PLAT COUD SORT A SOUDER RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
| R12166 | 功能描述:烙鐵 Pencil Grip W/1/8" dia. C RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| R12168 | 功能描述:烙鐵 PENCIL GRIP HAND PIECE CARBON ELECTRO RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
發布緊急采購，3分鐘左右您將得到回復。