參數資料
型號： QT60161B-AS
廠商： Electronic Theatre Controls, Inc.
英文描述： 16 KEY QMATRIX KEYPANEL SENSOR IC
中文描述： 16個主要QMATRIX KEYPANEL傳感器IC
文件頁數： 10/36頁
文件大小： 683K
代理商： QT60161B-AS
command to the device. The part will wake and the null
command will not be processed. The MOSI line in turn
requires a pullup resistor to prevent the line from floating low
and causing an unintentional wake from sleep.
During Sleep the oscillator is shut down, and the part
hibernates with microamp levels of current drain. When the
part wakes, the part resumes normal functionality from the
point where it left off. It will not recalibrate keys or engage in
other unwarranted behavior.
J
ust before going to sleep the part will respond with a
response of '
Z
'. In slave-only SPI mode (see Section 4.3), the
SS line must be floated high by the host as soon as it
receives this response; if SS does not float high, sleep will fail
and the device will instead completely reset after about 2
seconds. Upon waking the part will issue another '
Z
' byte
back to the host.
Noise sync:
See also command ^W,
page 26
. External fields can cause
interference leading to false
detections or sensitivity shifts. The
strongest external fields usually
come from AC power. RF noise
sources are heavily suppressed by
the low impedance nature of the QT
circuitry itself.
External noise only becomes a
problem if the noise is uncorrelated
with signal sampling; uncorrelated
noise can cause aliasing and beat
effects in the key signals. To
suppress this problem the devices
feature a noise sync input which
allows bursts to synchronize to the
noise source. This same input can
also be used to wake the part from a
low-power Sleep state.
The device
’
s bursts can be
synchronized to an external source
of repetitive electrical signal, such as
50Hz or 60Hz, or possibly a video
display vertical sync line, using the
Sleep
_
wake / Noise sync line. The
noise sync operating mode is set by
command ^W. This feature allows
dominant external noise signals to
be heavily suppressed, since the
system and the noise become
synchronized and no longer beat or
alias with respect to each other. The
sync occurs only at the burst for key
0 (X0Y0); the device waits for the
sync signal for up to
100ms after the
end of a preceding full matrix scan
(after key
#
15), then when a negative
sync edge is received, the matrix is
scanned in its entirety again.
The sync signal drive should be a
buffered logic signal, or perhaps a
diode-clamped signal, but never a
raw AC signal from the mains.
Since Noise sync is highly effective
yet simple and inexpensive to implement, it is strongly
advised to take advantage of it anywhere there is a possibility
of encountering electric fields. Quantum
’
s QmBtn software
can show signal noise caused by nearby AC electric fields
and will hence assist in determining the need to make use of
this feature.
If the sync feature is enabled but no sync signal exists, the
sensor will continue to operate but with a delay of 100ms
from the end of one scan to the start of the next, and hence
will have a slow response time.
3.15 LED / Alert Output
Pin 40 is designed to drive a low-current LED, 5mA
maximum, in an active-low configuration. Higher currents can
cause significant level shifts on the die and are not advised.
The LED will glow brightly (i.e. pin 40 will be solid low) during
calibration of one or more keys, for example at startup. When
a key is detected, the LED will pulse low for the duration of
Quantum Research Group Ltd.
l
Q
10
www.qprox.com QT60161B / R1.03
Figure 3-2 Recommended Circuit Diagram
相關PDF資料
PDF描述
QT60320-S IC-SMD-QPROX MATRIX SENSOR
QT60320 D-SUB CONN
QT60320-AS 32 KEY QMATRIX CHARGE TRANSFER IC
QT60320D 32 KEY QMATRIX CHARGE TRANSFER IC
QT60640-S IC-SMD-QPROX MATRIX SENSOR
相關代理商/技術參數
參數描述
QT60161B-ASG 功能描述:IC SENSOR MTRX TOUCH 16CH 44TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QMatrix™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
QT60161B-ASG-SL739 功能描述:電容觸摸傳感器 Qtouch IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
QT60161-S 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:16 KEY QMatrix KEYPANEL SENSORS IC
QT60168 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:16, 24 KEY QMATRIX ICs
QT60168-AG 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:16, 24 KEY QMATRIX ICs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*