- 您現在的位置：買賣IC網 > PDF目錄361325 > QT310-D (Electronic Theatre Controls, Inc.) PROGRAMMABLE CAPACITANCE SENSOR IC PDF資料下載
參數資料
| 型號： | QT310-D |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | PROGRAMMABLE CAPACITANCE SENSOR IC |
| 中文描述： | 可編程電容傳感器IC |
| 文件頁數： | 13/20頁 |
| 文件大?。?/td> | 837K |
| 代理商： | QT310-D |
Likewise, RF emissions are sharply curtailed by the use of
RE1, which bandwidth limits RF emissions based on the value
of RE1 and Cx, the electrode capacitance.
3.5.1 L
INE
C
ONDUCTED
EMI
Line conducted EMI can be reduced by making sure the
power supply is properly bypassed to chassis ground. The
OUT line can also be paths for conducted EMI, and these can
be bypassed to circuit ground with an RC filter network. The
additional resistors RE2 through RE5 can also help with
conducted EMI.
3.5.2 S
PREAD
-S
PECTRUM
M
ODULATION
The QT310 uses spread-spectrum burst modulation to
dramatically reduce susceptibility to external noise sources.
Spread-spectrum is implemented using frequency hopping
between four ‘channels’ centered around 240kHz. The
frequency of operation is altered with each successive burst;
the total frequency spread is approximately ±7%.
Spread-spectrum operates full-time and cannot be disabled.
If the DIAT (Detect Integrator terminal count) is set to DIAT=2,
then two different frequencies will be used to determine a
detection result. There is no way to control which two
frequencies are used, but they are guaranteed to be different.
If the DIAT (Detect Integrator) is set to 4 or higher, the
detection process will take advantage of all four possible
frequencies before confirming a result. All it takes is one
‘clear’ frequency for a false detection to be suppressed, since
a non-detection on one sample is enough to clear the DI
counter and abort a pending detection.
4 Parameter Cloning
The cloning process allows user-defined settings to be loaded
into internal eeprom, or read back out, for development and
production purposes.
The QTM300CA cloning board in conjunction with QT3View
software simplifies the cloning process greatly. The E3B eval
board has been designed with a connector to facilitate direct
connection with the QTM300CA. The QTM300CA in turn
connects to any PC with a serial port which can run QT3View
software (included with the QTM300CA and available free on
Quantum’s web site).
The connections required for cloning are shown in Figure 4-1.
Further information on the cloning process can be found in
the QTM300CA instruction guide. Section 3.3.2 above
discusses wiring issues associated with cloning.
The parameters which can be altered are shown in Table 4-1,
page 14.
It is possible for a host controller to read and change the
internal settings via the interface connections shown, but
doing so will disturb the sensing process even when data
transfers are not occurring. The additional capacitive loading
of the interface pins will contribute to Cx; also, noise on the
interface lines can cause erratic operation.
The internal eeprom has a life expectancy of 100,000
erase/write cycles.
A serial interface specification for the device can be obtained
by contacting Quantum.
L
Q
13
QT310/R1.03 21.09.03
相關PDF資料 |
PDF描述 |
|---|---|
| QT310-IS | PROGRAMMABLE CAPACITANCE SENSOR IC |
| QT320 | 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC |
| QT320-D | 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC |
| QT320-IS | 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC |
| QT60040-S | IC-SMD-QPROX MATRIX SENSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QT310-IS | 功能描述:SENSOR IC TOUCH PROG 1CH 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QProx™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| QT310-ISG | 制造商:Quantum Corp 功能描述:TOUCH SENSOR 1 CHAN SOIC8 310 ((NW)) |
| QT310-ISG SL775 | 制造商:Atmel Corporation 功能描述:TOUCH PRODUCT - Bulk |
| QT310-S | 功能描述:SENSOR IC TOUCH PROG 1CH 8-SOIC 制造商:microchip technology 系列:QProx?? 包裝:管件 零件狀態:停產 觸摸屏:2 線電容 分辨率（位）:16 b 接口:串行 電壓基準:內部 電壓 - 電源:1.8 V ~ 5 V 電流 - 電源:600μA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.209"，5.30mm 寬） 供應商器件封裝:8-SO 基本零件編號:QT310 標準包裝:95 |
| QT320 | 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC |
發布緊急采購，3分鐘左右您將得到回復。