- 您現在的位置：買賣IC網 > PDF目錄361324 > QT113 (Electronic Theatre Controls, Inc.) CHARGE-TRANSFER TOUCH SENSOR PDF資料下載
參數資料
| 型號： | QT113 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | CHARGE-TRANSFER TOUCH SENSOR |
| 中文描述： | 電荷轉移觸摸傳感器 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 180K |
| 代理商： | QT113 |
Electromechanical devices like relays will usually ignore this
short pulse. The pulse also has too low a duty cycle to visibly
affect LED’s. It can be filtered completely if desired, by
adding an RC timeconstant to filter the output, or if interfacing
directly and only to a high-impedance CMOS input, by doing
nothing or at most adding a small non-critical capacitor from
Out to ground (Figure 2-5).
The QT113H variant has an active-high output; the heartbeat
signal of the QT113H works in exactly the same manner.
2.2.4 O
UTPUT
D
RIVE
The QT113’s `output is active low and can sink up to 5mA of
non-inductive current. If an inductive load is used, such as a
small relay, the load should be diode clamped to prevent
damage. When set to operate in a proximity mode (at high
gain) the current should be limited to 1mA to prevent gain
shifting side effects from occurring, which happens when the
load current creates voltage drops on the die and bonding
wires; these small shifts can materially influence the signal
level to cause detection instability as described below.
Care should be taken when the QT113 and the load are both
powered from the same supply, and the supply is minimally
regulated. The QT113 derives its internal references from the
power supply, and sensitivity shifts can occur with changes in
Vdd, as happens when loads are switched on. This can
induce detection ‘cycling’, whereby an object is detected, the
load is turned on, the supply sags, the detection is no longer
sensed, the load is turned off, the supply rises and the object
is reacquired,
ad infinitum
. To prevent this occurrence, the
output should only be lightly loaded if the device is operated
from an unregulated supply, e.g. batteries. Detection
‘stiction’, the opposite effect, can occur if a load is
shed
when
Out is active.
The output of the QT113 can directly drive a resistively
limited LED. The LED should be connected with its cathode
to the output and its anode towards Vcc, so that it lights when
the sensor is active. If desired the LED can be connected
from Out to ground, and driven on when the sensor is
inactive.
The QT113H variant has an active-high output.
3 - CIRCUIT GUIDELINES
3.1 SAMPLE CAPACITOR
Charge sampler Cs can be virtually any plastic film or
medium-K ceramic capacitor. The acceptable Cs range is
from 10nF to 500nF depending on the sensitivity required;
larger values of Cs demand higher stability to ensure reliable
sensing. Acceptable capacitor types include polycarbonate,
PPS film, or NPO/C0G ceramic.
3.2 OPTION STRAPPING
The option pins Opt1 and Opt2 should never be left floating.
If they are floated, the device will draw excess power and the
options will not be properly read on powerup. Intentionally,
there are no pullup resistors on these lines, since pullup
resistors add to power drain if tied low.
The Gain input should be connected to either Vdd or Gnd.
Tables 1-1 and 2-1 show the option strap configurations
available.
3.4 POWER SUPPLY, PCB LAYOUT
The power supply can range from 2.5 to 5.0 volts. At 3 volts
current drain averages less than
600μA in most cases, but
can be higher if Cs is large. Increasing Cx values will actually
decrease
power drain. Operation can be from batteries, but
be cautious about loads causing supply droop (see
Output
Drive
, previous section).
As battery voltage sags with use or fluctuates slowly with
temperature, the QT113 will track and compensate for these
changes automatically with only minor changes in sensitivity.
If the power supply is shared with another electronic system,
care should be taken to assure that the supply is free of
- 6 -
Figure 2-4
Using a micro to obtain HB pulses in either output state
Figure 2-3
Getting HearBeat pulses with a pull-down resistor
+2.5 to 5
3
4
6
5
1
7
2
OUT
OPT1
OPT2
GAIN
SNS1
SNS2
Vss
Vdd
8
Ro
HeartBeat Pulses
Microcontroller
PORT_M.x
PORT_M.y
3
4
6
5
7
2
OUT
OPT1
OPT2
GAIN
SNS1
SNS2
R
o
Figure 2-5 Eliminating HB Pulses
3
4
6
5
7
2
OUT
OPT1
OPT2
GAIN
SNS1
SNS2
CMO S
100pF
C
o
GATE OR
MICRO INPUT
相關PDF資料 |
PDF描述 |
|---|---|
| QT113-D | CHARGE-TRANSFER TOUCH SENSOR |
| QT113-IS | CHARGE-TRANSFER TOUCH SENSOR |
| QT113-S | CHARGE-TRANSFER TOUCH SENSOR |
| QT113H | CHARGE-TRANSFER TOUCH SENSOR |
| QT113H-D | CHARGE-TRANSFER TOUCH SENSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QT113A-ISG | 功能描述:接口 - 專用 Qtouch IC RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| QT113B-ISG | 制造商:Atmel Corporation 功能描述:MICRO CONTROLLER |
| QT113-D | 功能描述:SENSOR IC TOUCH/PROXMTY 1CH 8DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QProx™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| QT113-DG | 功能描述:板機接口移動感應器和位置傳感器 INTEGRATED-CIRCUIT RoHS:否 制造商:Panasonic Electric Works 封裝 / 箱體:TO-5 感應距離:3 m 輸出類型:Digital 電源電壓-最大:6 V 電源電壓-最小:2.3 V 電源電流: 最大工作溫度:+ 60 C 封裝:Bulk |
| QT113-G | 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:CHARGE-TRANSFER TOUCH SENSOR |
發布緊急采購，3分鐘左右您將得到回復。