- 您現在的位置：買賣IC網 > PDF目錄361303 > QPI-6L (Vicor Corporation) 14 Amp Active EMI Filter for 48V DC Bus PDF資料下載
參數資料
| 型號： | QPI-6L |
| 廠商： | Vicor Corporation |
| 元件分類： | DC/DC變換器 |
| 英文描述： | 14 Amp Active EMI Filter for 48V DC Bus |
| 中文描述： | 14安培有源EMI濾波器的48V直流總線 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 172K |
| 代理商： | QPI-6L |
Applications Information
The QPI-6 is an active EMI filter providing conducted
common-mode and differential-mode attenuation
from 150 kHz to 30 MHz. The QPI-6 attenuates noise at
all frequencies covered by EN55022. Designers should
be aware that to select and qualify an EMI filter they
must test the filter in their equipment under the set up
and conditions specified in the EMI standards that they
are trying to meet.
Filter performance is highly dependent on several
factors and cannot be derived from the attenuation
curves shown in
Figure 2
alone. Performance is a
complex function of filter element impedances and
noise source impedances, which vary in magnitude and
phase over the frequency spectrum. Measurements
should be made in consultation with in-house
compliance testing or an independent EMI test facility.
Test Example
Figures 3 and 4
show the before and after plots of a
DC-DC converter noise profile to demonstrate the
performance of the QPI-6. The plots were taken using
the standard measurement technique and set up defined
in CISPR22. The results show the total noise spectrum
for a standard DC-DC converter under load compared
to the EN55022 Class B Quasi-peak detection limit.
The resulting plot in
Figure 4
shows the QPI-6 is
effective in reducing the total conducted noise
spectrum measured pre-filter to well below the
EN55022 Class B Quasi-peak detection limit.
Layout and Circuit
Application of the QPI-6 requires PCB layout practices
similar to those used with passive EMI filters. The circuit
in
Figure 6
and the PCB layout in
Figures 9 & 10
should
be used as a design guide to ensure successful
application of the QPI-6. Refer to the application note
QPI- AN1 for additional PCB layout recommendations.
Note: For optimum performance of the QPI-1 it is critical
to connect the QPI-1 Shield Plane (pins 5 & 6) to the
converter EMI Shield Plane (common point of C1-C4 "Y"
capacitors) thru RY as shown in Figure 6. If the safety
earth-ground connection (chassis or case) is connected in
the power conversion section of the PCB it should be at
the input bus of the QPI-1 Shield Plane, shown as the
optional connection in Figure 6. Connecting the converter
EMI shield plane directly to chassis ground may degrade
the QPI-1 attenuation performance. The typical value for
RY is 10 Ohms. The recommended part is a 5% tolerance
SMT1206 or similarly rated 0.25 W through-hole resistor.
Some systems may require the converter positive or
negative input or an output "terminal" to be connected to
PE (Protective Earth) ground for safety or other
considerations. When using the QPI in this situation this
"terminal" must be connected to the converter shield
plane created in the PCB layout under the converter.
Because the PE earth path may pass excessive current
under a fault condition the resistance of this path may be
limited to a low resistance value. To meet the resistance
requirement without degrading filter performance Ry can
be replaced by a 4.7uH inductor rated for the fault current
condition maintaining low power dissipation during a
fault until the protection device clears.
Picor Corporation www.picorpower.com
QPI-6L Data Sheet Rev. 2.0 Page 3 of 8
Figure 3 –
Conducted EMI profile of a DC-DC Converter
without filter.
Figure 4 –
Conducted EMI profile of a DC-DC Converter
with QPI-6.
相關PDF資料 |
PDF描述 |
|---|---|
| QPI-8EVAL1 | CAP 47UF 16V ELECT KMG RAD |
| QPI-8L | AdvencedTCA Hot-Swap Sip With Active EMI Filter |
| QPO-1-EVAL1 | QPO Evaluation Board |
| QPO-1-EVAL3 | QPO-1 Evaluation Board, Micro Foot Print DC-DC Converters |
| QPO-1-EVAL5 | QPO-1 Evaluation Board, Mini Foot Print DC-DC Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QPI-6LZ | 功能描述:FILTER 48V, 14A ACTIVE EMI RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:Picor®, QUIETPOWER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| QPI-6LZ-01 | 功能描述:IC INTERFACE FILTER RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:Picor®, QUIETPOWER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| QPI-7-CB1 | 制造商:Vicor Corporation 功能描述:QPI-7LZ DOSA STYLE EVALUATION BOARD |
| QPI-7-EVAL1 | 制造商:Vicor Corporation 功能描述:QPI-7LZ Universal Evaluation Board for 6 A 24 V Active EMI Filter w/ Hot-Swap |
| QPI-7L | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:ACTIVE EMI FILTER |
發布緊急采購，3分鐘左右您將得到回復。