- 您現在的位置：買賣IC網 > PDF目錄11792 > QLX4270RIQT7 (Intersil)IC EQUALIZER REC 2.7GBPS 46QFN PDF資料下載
參數資料
| 型號： | QLX4270RIQT7 |
| 廠商： | Intersil |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC EQUALIZER REC 2.7GBPS 46QFN |
| 標準包裝： | 1 |
| 系列： | QLx™ |
| 應用： | 顯示端口 |
| 接口： | 串行 |
| 電源電壓： | 1.1 V ~ 1.3 V |
| 封裝/外殼： | 46-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 46-TQFN |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | QLX4270RIQT7-DKR QLX4270RIQT7-DKR-ND QLX4270RIQT7DKR |
5
FN6972.2
March 3, 2010
Control Pin Boost Setting
The voltages at the CP pins are used to determine the
boost level of each channel of QLx4270-DP. For each of
the four channels, k, the [A], [B], and [C] control pins
(CP[k]) are associated with a 3-bit non binary word.
While [A] can take one of two values, ‘LOW’ or ‘HIGH’,
[B] and [C] can take one of three different values: ‘LOW’,
‘MIDDLE’, or ‘HIGH’. This is achieved by changing the
value of a resistor connected between VDD and the CP
pin, which is internally pulled low with a 25kΩ resistor.
Thus, a ‘HIGH’ state is achieved by using a 0Ω resistor,
‘MIDDLE’ is achieved with a 25kΩ resistor, and ‘LOW’ is
achieved with an open resistance. Table 1 defines the
mapping from the 3-bit CP word to the 18 out of 32
possible levels available via the serial interface on the
Evaluation Board kit.
If all four channels are to use the same boost level, then
a minimum number of board resistors can be realized by
tying together like CP[k][A,B,C] pins across all channels
k. For instance, all four CP[k][A] pins can be tied to the
same resistor running to VDD. Consequently, only three
resistors are needed to control the boost of all four
channels. If the CP Pins are tied together and the 25kΩ is
used, the value changes to a 3.125kΩ resistor because
the 25kΩ is divided by 4.
Channel Power-Down
The IS[k] pin powers down the equalizer channel when
pulled low. This feature allows individually to power down
unused channels and to minimize power consumption.
Example: for DisplayPort applications with 1 or 2 links,
the unused channels may be powered down to save
power. The current draw for a channel is reduced from
50mA to 3.8mA when powered down.
Output Return Loss
(Com. to Diff.
Conversion)
SDC22
50MHz to 1.35GHz
20
dB
Output Residual Jitter
2.7Gb/s; Up to 2m 38AWG standard twin-axial
cable (11.5dB loss)
0.15
0.2
UI
Output Transition Time
tr, tf
20% to 80%
30
60
100
ps
Lane-to-Lane Skew
50
ps
Propagation Delay
From IN[k] to OUT[k]
500
ps
NOTES:
4. After channel loss, differential amplitudes at QLx4270-DP inputs must meet the input voltage range specified in “Absolute
5. Temperature = +25°C, VDD = 1.2V.
6. Output residual jitter is the difference between the total jitter at the lane extender output and the total jitter of the transmitted
signal (as measured at the input to the channel). Total jitter (TJ) is DJpp + 14.1 x RJRMS.
7. Measured using a PRBS 27-1 pattern. Deterministic jitter at the input to the lane extender is due to frequency-dependent,
media-induced loss only.
8. Rise and fall times measured using a 1GHz clock with a 20ps edge rate.
Electrical Characteristics VDD = 1.2V, TA = +25°C, and VIN = 800mVP-P, unless otherwise noted. (Continued)
PARAMETER
SYMBOL
CONDITION
MIN TYP
MAX UNITS NOTES
TABLE 1. MAPPING BETWEEN CP-SETTING RESISTOR
AND QLx4270-DP BOOST LEVELS
RESISTANCE BETWEEN CP PIN
AND VDD
SERIAL BOOST
LEVEL
CP[A]
CP[B]
CP[C]
Open
0
Open
25kΩ
2
Open
0Ω
4
Open
25kΩ
Open
6
Open
25kΩ
8
Open
25kΩ
0Ω
10
Open
0Ω
Open
12
Open
0Ω
25kΩ
14
Open
0Ω
15
0Ω
Open
16
0Ω
Open
25kΩ
17
0Ω
Open
0Ω
19
0Ω
25kΩ
Open
21
0Ω
25kΩ
23
0Ω
25kΩ
0Ω
24
0Ω
Open
26
0Ω
25kΩ
28
0Ω
31
TABLE 1. MAPPING BETWEEN CP-SETTING RESISTOR
AND QLx4270-DP BOOST LEVELS (Continued)
RESISTANCE BETWEEN CP PIN
AND VDD
SERIAL BOOST
LEVEL
CP[A]
CP[B]
CP[C]
QLx4270-DP
相關PDF資料 |
PDF描述 |
|---|---|
| AT90CAN64-15AZ | MCU AVR 64K FLASH 15MHZ 64TQFP |
| AT90CAN64-15MZ | MCU AVR 64K FLASH 15MHZ 64-QFN |
| AT32UC3A0256-ALUR | IC MCU AVR32 256K FLASH 144LQFP |
| DS80C390-FCR+ | IC MPU CAN DUAL HS 64-LQFP |
| VI-BTH-IW-F2 | CONVERTER MOD DC/DC 52V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QLX4300-S45 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Lane Extender |
| QLX4300SIQSR | 功能描述:接口 - 專用 3 GBS QD CH LANE EXTENDER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| QLX4300SIQT7 | 功能描述:接口 - 專用 4 GBS QD CH LANE EXTENDER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| QLX4600LIQSR | 功能描述:接口 - 專用 6 GBS QD CH LANE EXTENDER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| QLX4600LIQT7 | 功能描述:接口 - 專用 6 GBS QD CH LANE EXTENDER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。