- 您現在的位置：買賣IC網 > PDF目錄69294 > PWR-82331-310L (DATA DEVICE CORP) BRUSHLESS DC MOTOR CONTROLLER, 50 A, DMA26 PDF資料下載
參數資料
| 型號： | PWR-82331-310L |
| 廠商： | DATA DEVICE CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 50 A, DMA26 |
| 文件頁數： | 2/17頁 |
| 文件大?。?/td> | 631K |
| 代理商： | PWR-82331-310L |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
10
Data Device Corporation
www.ddc-web.com
PWR-82331 and PWR-82333
P-02/05-0
GROUND CONNECTIONS
LAYOUT AND EXTERNAL COMPONENTS
Important: The following layout guidelines and required external
components are critical to the proper operation of these motor
drives.
External connections can be easily made to the hybrid by any of
the following methods:
Solder a wire around each pin.
Use pin extenders to raise the height of each pin so a print-
ed circuit board can be mounted on top of the hybrid.
Use a printed circuit board with a cutout that will enable the
printed circuit board to slide over the pins.
Permanent damage will result to the motor drive if the user
does not make the following recommended ground connec-
tions that will ensure the proper orientation of the hybrid.
The Vb and logic grounds are on pins 19, 22 and 26 (GND). The
VSS connections for the output stage are on pins 1, 5, and 8
(VSS). To prevent damage to the internal drive circuitry, the
differential voltage between the GND (pins 19, 22, 26) and
VSS (pins 1, 5, 8) must not exceed ± 3 V max, dc or peak.
This includes the combined voltage drop of the associated
ground paths and the voltage drop across RSENSE (see FIG-
URE 12).
For example, a value for RSENSE of 0.025
will give a voltage
drop of +1.25 V at 50 A and allow enough margin for the voltage
drop in the ground conductors. Locate RSENSE 1" - 2" maximum
from the hybrid. It is critical that all ground connections be as
short, and of lowest impedance, as the system allows.
C1, C2, and C3 are 1 mF, +10 V ceramic capacitors that provide
a low ac impedance between Vss pin and GND.You must use one
capacitor for each VSS pin-to-GND connection (total of three
capacitors in all), these capacitors are independent of the type of
drive scheme used. (i.e., Trapezoidal or Sinusoidal drive). Since
placement of these capacitors is critical, place these capacitors
across the hybrid, if possible. Please note, on FIGURE 12, that
C1, C2, and C3 must go directly from terminal-to-terminal on the
hybrid - do not daisy chain along the ground return.
C4, C5, and C6 are the 0.1 mF ceramic bypass capacitors that
suppress high frequency spiking. The voltage rating should be
two times the maximum system voltage. These capacitors
should be located as close to the hybrid as possible.
Care must be taken to control the regenerative energy produced
by the motor in order to prevent excessive spiking on the Vcc
line. Accomplish this by placing a capacitor or clamping diode
between the Vcc and the high-power ground return.
FIGURE 12. PWR-82331/82333 GROUND CONNECTIONS
C1, C2, C3 = 1 F, 10 V CERAMIC CAPACITORS
C4, C5, C6 = 0.1 F, CERAMIC CAPACITORS
C7 = 0.01 F, 100 V CERAMIC CAPACITORS
C7 = 0.01 F, 50 V CERAMIC CAPACITORS
相關PDF資料 |
PDF描述 |
|---|---|
| PWR-82333-210S | BRUSHLESS DC MOTOR CONTROLLER, 50 A, DMA26 |
| PWR-82331-220S | BRUSHLESS DC MOTOR CONTROLLER, 50 A, DMA26 |
| PWR-82331-860L | BRUSHLESS DC MOTOR CONTROLLER, 50 A, DMA26 |
| PWR-82333-110L | BRUSHLESS DC MOTOR CONTROLLER, 50 A, DMA26 |
| PWR-82333-820Q | BRUSHLESS DC MOTOR CONTROLLER, 50 A, DMA26 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PWR-82332 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Drives (Power Amplifiers)|3-Phase Bridge Drive. Flat Pack Hybrid with Formed Leads |
| PWR-82332-100 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver |
| PWR-82332-110 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver |
| PWR-82332-120 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver |
| PWR-82332-300 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver |
發布緊急采購，3分鐘左右您將得到回復。