- 您現在的位置：買賣IC網 > PDF目錄69257 > PTMA403033P2AST (TEXAS INSTRUMENTS INC) 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTMA403033P2AST |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-6 |
| 文件頁數： | 32/35頁 |
| 文件大小： | 1867K |
| 代理商： | PTMA403033P2AST |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁
www.ti.com
(Top View)
3
5
2
1
4
6
PTMA40XXXX
SLTS259B – FEBRUARY 2006 – REVISED MAY 2007
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NAME
NO.
The Enable input is an open-base logic input that is referenced to VI–. Two ON/OFF enable options are available,
positve logic and negative logic. Positive logic devices are enabled by applying a logic high voltage (Open) and
are disabled by applying a logic low voltage (VI–). Negative logic devices are enabled by applying a logic low
voltage (VI–) and are disabled by applying a logic high voltage (Open). See the Application Information section for
Enable/Sync (1)
3
more detailed information.
This pin also has the option of a synchronization input. A module that has the synchronization option does not
have ON/OFF enable control. A 5-V logic signal greater than the free-running frequency but
≤ 350 kHz is required
for synchronization control. See the Application Information section for more detailed information.
The negative input supply for the module, and the 0-V reference for the Enable/Sync inputs. When powering the
VI–(1)
2
module from a positive source, this input is connected to the input source return.
The positive input for the module with respect to VI–. When powering the module from a negative input voltage,
VI+ (1)
1
this input is connected to the input source ground.
VO+
4
This is the positive power output with respect to VO–. It is dc isolated from the input power pins.
This pin allows the output voltage set point of the module to be increased or decreased up to
± 10 %. Connecting
a resistor between this terminal and VO+ decreases the output voltage set point. Connecting a resistor between
this terminal and VO– increases the output voltage set point. A 0.05-W rated resistor may be used, with tolerance
Trim
5
and temperature stability of 1% and 100 ppm/
°C, respectively. If left open circuit, the converter output voltage
defaults to its nominal value. The specification table gives the standard resistor values for the most common
output voltages.
This is the output power return for the VO+ bus. This terminal should be connected to the common of the load
VO–
6
circuit.
(1)
These functions indicate signals electrically common with the input.
6
相關PDF資料 |
PDF描述 |
|---|---|
| PTMA402050N1AZT | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| PTMA401120A2AST | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| PTMA401120A2AZT | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| PTMA401120A3AST | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| PTMA401120N2AD | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTMA403033P2AZ | 功能描述:DC/DC轉換器 10W 36V-75Vin 1500V Iso DC-DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTMA403033P2AZT | 功能描述:DC/DC轉換器 10W 36V-75Vin 1500V Iso DC-DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTMB100A6 | 制造商:NIEC 制造商全稱:Nihon Inter Electronics Corporation 功能描述:IGBT MODULE Six-Pack 100A 600V |
| PTMB100A6C | 制造商:NIEC 制造商全稱:Nihon Inter Electronics Corporation 功能描述:IGBT SP series Six-Pack 100A 600V |
| PTMB100B12 | 制造商:NIEC 制造商全稱:Nihon Inter Electronics Corporation 功能描述:IGBT MODULE Six-Pack 100A 1200V |
發布緊急采購，3分鐘左右您將得到回復。