- 您現在的位置：買賣IC網 > PDF目錄69255 > PTH12060WAH (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTH12060WAH |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-10 |
| 文件頁數： | 8/29頁 |
| 文件大?。?/td> | 1040K |
| 代理商： | PTH12060WAH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Q1VDS (2 V/div)
VO (2 V/div)
II (2 A/div)
t Time 40 ms/div
SLTS217H – MAY 2003 – REVISED DECEMBER 2008 .................................................................................................................................................... www.ti.com
Figure 11. Power-Up from Track Control
NOTE:
If a prebias condition is not present, it is highly recommended that the Track control
pin be used for controlled power-up and power-down. If Track control is not used, the
output voltage starts up and overshoots by as much as 10%, before settling at the
output voltage setpoint.
How Auto-Track Works
Auto-Track works by forcing the module output voltage to follow a voltage presented at the Track control pin (1).
This control range is limited to between 0 V and the module set-point voltage. Once the track-pin voltage is
raised above the set-point voltage, the module output remains at its set-point (2). As an example, if the Track pin
of a 2.5-V regulator is at 1 V, the regulated output is 1 V. If the voltage at the Track pin rises to 3 V, the regulated
output does not go higher than 2.5 V.
When under Auto-Track control, the regulated output from the module follows the voltage at its Track pin on a
volt-for-volt basis. By connecting the Track pin of a number of these modules together, the output voltages follow
a common signal during power up and power down. The control signal can be an externally generated master
ramp waveform, or the output voltage from another power supply circuit (3). For convenience, the Track input
incorporates an internal RC-charge circuit. This operates off the module input voltage to produce a suitable rising
waveform at power up.
16
Copyright 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): PTH12060W/L
相關PDF資料 |
PDF描述 |
|---|---|
| PTH12060LAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12060YAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH03060YAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH05060YAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH05060YAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH12060WAH | 制造商:POWER TRENDS 功能描述:IC DC/DC 12VIN 10A ADJ O/P 12060 |
| PTH12060WAHT | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| PTH12060WAS | 功能描述:DC/DC轉換器 1.2 to 5.5V 10A 12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12060WAST | 功能描述:DC/DC轉換器 1.2 to 5.5V 10A 12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12060WAZ | 功能描述:DC/DC轉換器 10.8-13.2Vin 5.5V10A 0.995" x0.620"x0.354 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。