- 您現在的位置：買賣IC網 > PDF目錄69255 > PTH12060LAZT (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTH12060LAZT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, DIP-10 |
| 文件頁數： | 23/29頁 |
| 文件大?。?/td> | 1040K |
| 代理商： | PTH12060LAZT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁
ELECTRICAL CHARACTERISTICS
www.ti.com .................................................................................................................................................... SLTS217H – MAY 2003 – REVISED DECEMBER 2008
TA = 25C; VI = 12 V; VO = 3.3 V; CI = 560 F, CO = 0 F, and IO = IOmax (unless otherwise stated)
PTH12060W
UNIT
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
TA = 60°C, 200 LFM airflow
0
10
(1)
A
IO
Output current
Over
ΔVadj range
TA = 25°C, natural convection
10
(1)
A
VI
Input voltage range
Over IO range
10.8
13.2
V
VO tol
Set-point voltage tolerance
±2
(2)
%VO
ΔRegtemp
Temperature variation
–40°C < TA < 85°C
±0.5
%VO
ΔRegline
Line regulation
Over Vin range
±10
mV
ΔRegload
Load regulation
Over Io range
±12
mV
ΔRegtot
Total output variation
Includes set-point, line, load, –40°C
≤ TA ≤ 85°C
±3
%VO
ΔVadj
Output voltage adjust range
Over Vin range
1.2
5.5
V
RSET = 280 , VO = 5.0 V
94%
RSET = 2.0 k, VO = 3.3 V
92%
RSET = 4.32 k, VO = 2.5 V
90%
η
Efficiency
IO = 8 A
RSET = 11.5 k, VO = 1.8 V
87%
RSET = 24.3 k, VO = 1.5 V
85%
RSET = open circuit, VO = 1.2 V
83%
VO ≤ 2.5 V
25
(3)
mVPP
20-MHz bandwidth,
VO ripple (peak-to-peak)
with CO2 = 10 F ceramic
VO > 2.5 V
1
(3)
%VO
IO trip
Overcurrent threshold
Reset, followed by auto-recovery
20
A
ttr
1 A/s load step, 50 to
Recovery time
70
S
Transient response
100% Iomax,
Vo over/undershoot
100
mV
ΔVtr
CO1 = 330 F
VOadj
Margin up/down adjust
±5%
IILmargin
Margin input current (pins 9/10)
Pin to GND
–8
(4)
A
IILtrack
Track input current (pin 8)
Pin to GND
–0.11
(5)
mA
dVtrack/dt
Track slew rate capability
CO ≤ CO (max)
1
V/ms
VI increasing
9.5
10.4
UVLO
Undervoltage lockout
V
VI decreasing
8.8
9
VIH
Input high voltage, Referenced to GND
Open
(5)
V
VIL
Inhibit Control (pin 3)
Input low voltage, Referenced to GND
–0.2
0.5
IIL
Input low current, Pin 3 to GND
0.24
mA
II
Input standby current
Inhibit (pin 3) to GND, Track (pin 8) open
10
mA
f s
Switching frequency
Over VI and IO ranges
300
350
400
kHz
CI
External input capacitance
560
(6)
F
Nonceramic
0
330
(7)
5500
(8)
Capacitance value
F
CO
External output capacitance
Ceramic
0
300
Equivalent series resistance (nonceramic)
4
(9)
m
6.4
MTBF
Reliability
Per Bellcore TR-332, 50% stress, TA = 40°C, ground benign
10
6 Hr
(1)
See SOA curves or consult factory for appropriate derating.
(2)
The set-point voltage tolerance is affected by the tolerance and stability of RSET. The stated limit is unconditionally met if RSET has a
tolerance of 1% with 100 ppm/°C or better temperature stability.
(3)
The peak-to-peak output ripple voltage is measured with an external 10-F ceramic capacitor. See the standard application schematic.
(4)
A small, low leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc.
(5)
This control pin has an internal pull-up to the input voltage VI. If it is left open-circuit, the module operates when input power is applied.
A small, low-leakage (<100 nA) MOSFET or open-drain/collector voltage supervisor IC is recommended for control. Do not place an
external pull-up on this pin. For further information, see the related application information section.
(6)
A 560 F input capacitor are required for proper operation. The electrolytic capacitor must be rated for a minimum of 1050 mA rms of
ripple current.
(7)
An external output capacitor is not required for basic operation. Adding 330 F of distributed capacitance at the load improves the
transient response.
(8)
This is the calculated maximum. The minimum ESR limitation oftens result in a lower value. When controlling the Track pin using a
voltage supervisor, CO(max) is reduced to 2200 F. See the application notes for further guidance.
(9)
This is the typical ESR for all the electrolytic (nonceramic) output capacitance. Use 7 m
as the minimum when using max-ESR values
to calculate.
Copyright 2003–2008, Texas Instruments Incorporated
3
Product Folder Link(s): PTH12060W/L
相關PDF資料 |
PDF描述 |
|---|---|
| PTH12060YAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH03060YAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH05060YAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH05060YAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH03060YAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH12060W | 制造商:ARTESYN 制造商全稱:Artesyn Technologies 功能描述:DC/DC CONVERTERS POLA Non-isolated |
| PTH12060WAD | 功能描述:DC/DC轉換器 10.8-13.2Vin 5.5V10A 0.995" x0.620"x0.354 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH12060WADT | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC/DC CONVERTERS |
| PTH12060WAG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| PTH12060WAH | 功能描述:DC/DC轉換器 1.2 to 5.5V 10A 12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。